Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I have a MTD 10hp snowblower that is two years old.  While snowblowing I struck a small piece of wood and it bent one auger and the impeller.  Now I need to replace them.  There are two spring pins that hold the shaft into the impeller, can any one tell me how to remove them?

Wayne

I used a dremmel tool with a diamond cut off disk.  ran it right up the center and then popped it out with a screwdriver.  (This was on the shaft behind the impeller bearing which I had to hammer off with a pickle wrench)  Mind you, my machine is a 1978 Craftsman and  nobody had ventured into this unknown territory previously)

Good luck

Jon

They are roll pins, or splt pins as some people call them. To do this job you are better off to split the machine in half and remove the whole auger and impeller assembly as one unit. It has to come apart anyways to replace these parts. 

DNK1, thanks.  After looking at the manual and the blower I realized that taking the roll pins out will not free up the shaft and I need to take the whole machine apart.  Looks like a huge, complicated job, but I have no choice to give it a go.  I cant believe MTD couldnt design a simple way to replace the augers which is probably the part that needs to be replaced most often.  For example, instead of tack welding the sides, the could have bolted them in which would allow you to split the worm gear box open wide enough to  seperate the drive shaft from the auger shaft.  Great engineering MTD

I am disappointed to hear that removing the rolled spring pins doesn't allow the removal of the auger assembly - I have a brand new Craftsman 42" snowblower attachment on a 26 hp tractor and my wife picked up an electrical cord that ripped the shaft out of the bearing cap.  All seems to be intact except that I need to get the shaft back into the bearing cap.  I've unbolted both bearing caps and the upper brace that connects to the auger gear box and thought I only had to press out the rolled pins to remove the auger - not so????  If anyone knows for sure please respond as I am planning to try to pull these pins but won't bother if it won't do the trick.

Thanks for any help you can provide.

Rocky

Rocky7722 wrote:

In my old [1976] Bolens when the bearings on either end of the auger shaft are removed, you jiggle the whole deal a little, and the entire assembly comes out.

In the newer ones, first you need to remove the pulleys & a woodruff key on the end of the impeller shaft.

If you don't have it, there should be a parts breakdown on the sears.com site.  Look it over & see if you can do the same.

Jim

Jim,

Thanks for the info - I'll give that a try.  I did look at the parts breakdown and it appears that the shaft for the auger slides off when you remove the spring pins but there's also a key in the shaft as you described.  Guess there's no easy way is there?  I do know that I've told my wife to stay off the power equipment - every time she tries to help, it costs me time and money.  At least she's out there trying to help!!!

Thanks,

Rocky

Well I took Jim's advice and went from the back side of the snowthrower.  Appears the same engineer that designed Jim's snowblower also designed the Craftsman.  After removing the drive belt from the rear pulley, I removed the center bolt holding the pulley on the end of the shaft.  I then loosened the rear bearing holder and was able to move the entire assembly forward (after removing bolts on the front auger bearing cups).  Much easier than trying to remove the spring pins. 

Jim thanks for the advice it was right on.

Rocky

MTD auger case rebuild questions. In a last post a couple of things were not so clear to me. If I followed him right he:
1 opened up the bottom
2.removed the belt
3 unscrewed unscrewed the pully bolt
4.removed the cup bearing for the back end of the auger drive shaft
5.could pull out the auger after undoing it's two cup bearings.

My confusions are:
1.Aren't there three belts to remove?
2.You might be able to get a wrench in by the pully bolt but you'd have to life up the friction drive disk to get the bold our or later get at the bolts for the auger bearing cup.
3.Because of 2 I think you'd have to move the friction disk out of the way.
4.Because of 3 you'd have to remove the rubber tipped friction disk and because of that it's axle.

I wrote that and just went out to the machine and
1. removed the rubber friction disk axle and rubber friction disk.
2. Then removed the friction disk spring so could lift up the plate it rides on.
3. Removed the pully bolts, removed the pully bolts and removed the two pullys and it's three prong drive plate.
4. That exposed the far end of the auger drive shaft.

The new confusion is how to remove (then later replace) the three bolts that hold the bearing cup. The bolts are turning on bolts on the other side of the case. That is the bolts just in back of the impeller. I can probably wedge a wrench in there and after a while get the three bolts out but what happens later when I go to replace them?

To get them back in with the impeller in the way seems just about impossible. Is that what has to be done somehow???

Another question is and is the reason I'm doing the job it the impeller worm is turning ok but not driving the augers. There's a key in there that might be broken and I'm hoping it's just the key that's broken. If the auger worm is stripped I'm hosed I think.
If the key is ok and the gear it turns is stripped can I buy just that gear? The cheapest I've been able to find for the complete assembly is $160 plus shipping. I maybe got lucky and bought a junker on the net today which I have not seen but the guy says the auger is ok in that unit so I may be able to use that one.
The junker would need to be fixed and possibly need that gear.

The big question is how do I get that now loose auger assembly detached from the rear support cup bearing?