Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I'm restoring an old Ariens Sno Thro and one of the rakes is seemingly locked to the shaft. Guy at work put it on a 40 ton hydraulic press and it still didn't budge - just started distorting the rake. He didn't heat it though.

I have a second parts snowblower and the rake is stuck on that one as well. The difference is that one is on the "closed" side of the gearbox so I could remove the axle shaft if necessary.

I'm was thinking of getting as much penetrating oil on it as possible, putting a gear puller on it, leaving ot for a few days, tighten the puller, etc. Any other suggestions? Both gearboxes are nice and tight and they're the old cast iron ones so I'd like to rescue both of them.

I am planning to take it slowly to a small engine dealer in NH, who has had success getting them off by a combination of pressure and heat.

I made a press with a hydraulic jack and several days of lubing it and pressure did nothing but bend a 1/2" steel bolt.....

Garandman - once its off, you will need to clean up the shaft's insides. I used a long wooden dowel with a piece of sandpaper taped on. When reassembling, I used never-seize liberally to keep this from ever happening again. Hopefully heat & pressure will get these parts "divorced" . My cut tube had to be JB welded, ground down smoothly & painted to restore the part.

Marty

Yes, it was me that rotated the augers against themselves, except  I used a pair of 2x4s, not pipes.  I tried PB Blaster for about a week, along with applied tension from a gear puller on the shaft and some banging with a brass hammer- I don't really know if that did anything.  When I finally got the auger loose, I was also applying lots of heat (MAPP gas) during the process and just kept at it.  I did start one of the 2x4s on fire a little.  I also cooked one of the seals on the shaft. 

Someone else cracked the cast housing while trying the 2x4 thing, so be careful. 

I would not put a machine back together without freeing the auger.  Sort of like not having a shear pin. 

I still have the parts in my basement, ready to put back together.  Since the weather is still in the 80s and 90s, it's not on my radar yet.  Probably after the first frost. 

Good Luck

RalphS wrote:

That  "someone else" was me... I split the LH auger gearcase trying to separate mine because I wasn't careful!

Marty

From the advice of another dealer, you have to heat the tube up to a dull red to get it off.

I just have a Bernzomatic propane torch that doesn't seem like it will generate enough heat fast enough to do this. Should I buy another, but a MAPP gas torch (which doesn't seem like it would be a lot more effective) or use this opportunity to buy an oxy acetylene rig?

I have a couple gear pullers and also rigged up some steel brackets so that I can apply pressure with a 6 ton bottle jack. So I just have to get it hot enough without annealing it.

Garandman wrote:

NEVER exceed 15psi pressure on acetylene. (Above that, liquid acetone is drawn from the bottle and will self-ignite.)

I use traps that keep the flame from possibly tracing back the inside of the hose.

But Mapp gas might do it. Great big might. It does get much hotter than propane. Tip choice can be critical.

http://abbysguide.com/ope/discussions/3542-0-1.html

http://www.cbs.state.or.us/external/osha/hazards/regbrnot.htm

http://www.tpub.com/content/construction/14250/css/14250_78.htm

If you have powerpoint http://www.dep.state.pa.us/dep/deputate/minres/dms/website/training/inventory/oxyacetylene.ppt

Oh yea, no oil or grease near the top of the bottles. Not on any of the fittings either. If they are rusty, leave them rusty.

Don't want you to go boom.

Home Depot has a Bernzomatic Welding, Brazing, and Cutting Kit  using MAPP and Oxygen.

"Kit includes burner wand, hose, oxygen regulator, fuel gas valvem cylinder stand, MG9 16 oz. MAPP® Gas cylinder, OX9 1,1 cubic foot oxygen cylinder, spark lighter and 5 brazing/welding rods"

$50. Anyone using one?

Garandman - I was able to get my auger tubes "cherry red" with the Bernzomatic Mapp/Oxy setup you listed above. I like it's portability & ability to get stubborn bolts & nuts off. I haven't used it as a cutting torch yet, but I am very pleased with mine otherwise.

Marty

Great, thanks for the feedback, the small size and quick setup suit m needs so I'll give them a try.