Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I turned the key on and have no spark from the plug or even the plug wire when turning over the engine

How do I know if it is the coil magneto or the xstar module magneto?

It is a model 38180

I have not yet made any substantial progress on this machine.  I did see a flywheel on ebay that I was interested in purchasing.  I asked the seller if all three magnets on the flywheel he was selling for the CCR2000 had basically the same magnetic pull.  He stated that the middle one is the magnet and the outer two are just blanks.  Well there you have it I guess. 

I have 2 of these toro's that have been great. Last week I went to start one (38180)and it just wasn't feeling right. After about 10 aggressive pulls the rope came out...ugggg. Back into the garage I removed the pull cover and fix the cord. A few more pulls and I surrender to the fact that it's not going to start. Long story short..no spark. I checked all as mentioned, kill switch, spark plug, fly wheel gap etc. No luck with an unknown ign module I had in a draw and the other unit (38185) doesnt have a module I can borrow. My readings from the coil assembly are 1.1ohms and 11.4k ohms. In earlier post i read a max of just under 8k ohms for the primary. Is 11.4k out of range? I want to be sure before I purchase any parts. Thanks. Note: This flywheel has a single magnet and is very strong.

   The low reading is on the primary.  The high on the secondary.  Over 8 is high.  You mentioned going over everything so just a reminder that many people replace coils for problems in the sparkplug wire and boot.  You've probably already tried connecting one lead to the ground lead and worked the other inside the plug boot while twisting the boot/wire connection to check for a resistance change.  Before tossing it you might do what's the other poster tried as a last resort of pulling the plug wire from the body & etc....

i guess at this point it cant hurt to do a little dissecting on the spark plug wire now. will post findings.

I was wondering why the service manual list the same engine, 47P, for both my ccr2000's but yet they are different.

Well, its finally over guys!!  I waited and waited and found a coil and module used on ebay for a real good price ($30).  I removed the second coil upon which I had attached the new spark plug wire.  In its place, I installed the new ebay coil and gapped 'er to .011.  I attached the module to the rewind starter cowling.  Now this module is one of the original gold colored modules.  I gapped the plug to .030.  I did not even check for spark at this point.  I figured it sparks, great.  If not, the machine is going next to the garbage can for the local scrappers to pick up.  I then put everything else back together and hauled it upstairs from the basement to the garage.

In the garage, I plugged in the electric starter...here goes nothing.  She fired up!!!  and stayed fired up!!!   It was however surging rather badly but at least it was running. Not enough fuel I thought.   I went back to the computer and searched for surging CCR 2000's.  Some said to rebuild the carb (which I had done already).  Others mentioned that there is one adjusting screw on the carb.  I took a look at that on the CCR 2000 carb.  Normally I (as a rule) set low and high idle screws 1 to 1 1/2 turn out.  This adjusting screw I had originally set 1 and 1/2 turns out.  I turned the screw a little further out so that it was about 2 or 2 and 1/2 turns out from a seated position.  No surging at all.  Runs like a dream...hums like a bee! 

Thank you guys for all you help, suggestions, and input.  I appreciate it very much.

   You cured it, nice going. 

   If I read the post right the problem could have been the coil or module as both were replaced.    If the coil then that meant the original went bad, the replacement went bad and the fixed coil bad, all in the same way.  The same for the module.  The first was defective and the replacement defective both in the same way.  Given the way things happened it almost seems the first replacement module was defective in the same way as the original.   Overall a nasty problem with some bad Karma mixed in. 

Another success story here. After trying a used module (no known condition) I sprang for an ebay mega fire II ($18 shipped). Just spun it by hand a the spark was brighter then a super nova. Guess I'll be winterizing it and wait till next year. Looks like Long Island is getting an early spring. Thanks for the helpful info.

Nice.

That only took what?  Three months?  

Electrical problems can be a nightmare.  Particularly of parts being interchanged are of "unknown" status. 

Hello all,
New to forum. Just joined.
I want to thank you all for this forum and especially this particular thread. I bought one of these Toro CCR 2000 snow blowers from a guy on craigslist. It is a 1995 mdl 38180 w/ the Suzuki engine. It looks as if it has hardly been used. Not a speck of rust and the engine is extremely clean. It had a no fire issue. I got it for a really good price.
I googled "Toro CCR 2000 no fire" and found this forum.
I read about halfway through this thread and ordered a Mega Fire ll. Before I ordered it I just gave everything a kind of going over. I took the engine out and looked at the coil and set the air gap at 0.010. Kind of looked over the wires but I just knew there was nothing wrong there. Put the engine in a vise and fabbed a pull rope to see if it was doing anything. I felt a weak shock was all.
Long story short I took the ignition module off and put the whole thing back together and waited for the new module. It came today and I had the snow blower running in just a few minutes. It started on the very first pull.
Thanks again!
Joe