Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I turned the key on and have no spark from the plug or even the plug wire when turning over the engine

How do I know if it is the coil magneto or the xstar module magneto?

It is a model 38180

Denny wrote: Jan 25 2011
Denny, The xstar module went south on my 1992 Toro CCR2000 snowblower and after reading about your fix I also installed a Mega Fire II. The machine started right up. I ran it about five minutes,seems good. The next time I blow snow will be a better test. Actually it was this sight that led me to my problem. Thanks to all. 

Blew snow yesterday with that little Toro for about a half hour after installing a $20 Stens Mega Fire II module. Ran great ,seems good.

Where do I order this mega fire II and how do I replace it?  My twenty year old CCR2000 will not restart after using it for a while until it gets cold again........All I have ever done to this machine is change the plug every year and replace the paddles once. Thanks

   Crapping out after running or a while and having to wait for cool-down to restart is typical with a bad plug.  You just might get away with a plug replacement

New plug every year..............same result. Runs great as long as I don't try to restart after running it for twenty minutes or so. I have gotten used to doing the entire drive way and walks without stopping. Still would like to know about ordering the replacement module and any tips about installing it. Thanks again.

   Have you tried testing for spark after gettnig hot and no restart?

trouts2 wrote:
I have a spark plug tester and when the Toro won't start after running for a while I get no spark across the gap also no spark from the wire to the plug. Still would like to know where to order the module and any tips on how to install it.

Hi fellas;

If anyone is still out here with some ideas, I sure could use your input!

I have become the lawnmower/snowblower repair guy for the guys at work.  I am about 99.9% successful with my repairs but this one has stumped me.  A friend gave me his Toro CCR 2000 snowblower for repair because the local shop wanted 600+ for repairs.  It is the 38185 with serial number 2001010.

No spark here.  I checked and cleaned all connections and re assembled with dielectric tune up grease.  Switch is ok.  I checked the ig modulator with a multi meter and got continuity (which I am assuming is a good thing).  Any way, I purchased a mega star II ignition module and put it in place of the original module.  Still no spark.  (spark plug is good though).  I checked the coil by placing my multi meter from the red wire of the coil to the spark plug terminal.  NO continuity.  I located and bought a used coil from a local shop for $55 .  Yippie...I got spark.  I then put it all back together.  (I had also cleaned the carb and replaced several parts there in).  She started on the first pull!  It ran excellent for 30 seconds and then quit.  No more spark.  I took everything apart again and found the module still had continuity but the coil did not (when I checked from the red wire to the spark plug terminal). 

How could that coil go shot so quickly?  I just hate to junk the machine.  I saw on ebay a coil/modulator combo for about $75.  I dont mind spending that but I also do not know if it is worth the risk.  That may go shot real quick.  What are your thoughts guys?  Thanks very much.

Not sure how much to believe your story about $600 repair cost when you can buy a brand new one (Toro 418) for around $350 with 2 year warranty.

broncman wrote:

l would first Double check the small wire that goes to ground from coil and make sure u have a GOOD and CLEAN bare metal connection there....also lve have replaced alot of those kill switchs so that may be your issuse... clean the ground connection and disconnect the kill switch then see if u got spark...if not u got a bad coil....l dont recall having to replace a coil on that motor before... and the odds of another coil going bad seems unlikely but it happens...