Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

   Picked up a Deere 826 yesterday.  The thing crapped out during the last storm with a brunt belt and the guy hurt is back shoveling so it got the boot. 

   Nice old buzzard rig but I can't find anything on it at the Deere site.  Anyone know where I can an exploded view?  I tried the usual places that have them and nothing on this one.   It's ID plate has P826J, 127489.  If I google P826J I get new models.  Nothing on the other number.

   The thing works fine after a belt replacement but it only tosses 3 - 8 feet with lots of low splatter.  I tried a few different belt sizes and tensions, and even over tight to insure no slip.  I can't see any slip with the cover off.  It has good grab, no crud in the V's, no obstruction in the housing.  It does have quite a distance from the arms to the lining, 1/2 inch.  The impleller is a 4 blade 12 inch and it should toss fairly well, 15-25. 

   Does anyone have this model and could tell me what it tosses like?  I can't see any problems so guess it's a design problem but at 3-8 feet hard to imagine they could make something that bad. 

   The motor certainly is not the problem, a Briggs Intek Snow 11hp a couple of years old.  I can drive into any condition snow and toss the same distance without engine sag.  Very impressive.  Anyone have a URL to an exploded view on the engine?  I can find one so I assume it a special for some maker.  It's got a 3/4 shaft.  3BSXS 3422HT 275387.  I can't get anything found at the Briggs site.  Googling I get 275385 which is a 10hp but nothing for 275487.  There are lots of hits for 3BXSX 3422HT but no motor like this.

ahw2698 wrote:

That's great and about what I figured.  It would bring it just into acceptable.  If you put a three inch pulley on that it would get it even better.  I tried on mine but without a kit it did not make any difference.   I think the Deere is nice and like the auger clutch allowing a free hand.  It's like the old Ariens machines which are very easy to use.  The Deere seems very well built and mine is clean without rust.  I hate to just have it languish or get the boot for $50.

trouts2 wrote:
That sounds like a fun project for a nice summer day. If it's a bearing with a 2 or 3 hole flange, it wouldn't be too hard to move it over 1/4", or even swap out for a flanged bearing.  Maybe there's even a bigger impeller in your parts pile?

Edit to add: Just looked it up in the parts list. 3 hole flange on the bearing, that's good. But it looks like the impeller and shaft are one piece (?), if so, no swapping the impeller. Though it should make it easier to drill for the kit while it's apart.

What would it entail for me to step up to a 3 inch pully? What I have now is a "two in one" style pulley. One piece of metal with two wheels of the same diameter (2 1/2 I think). I would assume I would keep the drive pulley to same diameter and jump the auger pulley up to 3"? Would I be able to do this with two individual pulleys, or would I have to get a double with the 3 inch / 2.5 inch combo? 

The other question I have would be with what size auger belt I would need with the bigger pulley. Is sizing for that going to be trial and error?

Does the auger shaft wobble around in the bearing?  Maybe you just have a very warb bearing.

Woof, At least on mine the auger support bearing is fine. 

ahw,

   Double or single is ok.   Murrays have a dual that can be used.  I had to go up an inch on mine going from 2.5 to 3.  HW stores are pretty good about exchanging or returning belts.  If you can't locate pulleys email me for a possible second hand source.  Email at link below.

I recently picked up an 826 from my Brother in Law.  I have the front end disassembled and have decided to implement some of the changes discussed in this thread.  I am going to purchase the auger kit.  I have already done minor repairs to the auger where it was bent, probably from stones.  I would like to look for a replacement pulley that is either a 2.5/3 or even a 2.5/3.5.  Can anyone tell me the best way to find such an item.  My experience in the past is that to get a part you really need a part number.   I have picked up a couple of the auger bearings from JD and noticed they have changed a little.  They are a little longer now and have a grease seal on them.  maybe they will last a little longer.

I would say have a look here or a local Tractor Supply Company.
http://www.mfgsupply.com/mower/mowerpull.html

http://www.tractorsupply.com/