Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens 926 hard to operate

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
BALR1415


Location: Northern Worcester County MA
Joined: Jan 13, 2011
Points: 9

Ariens 926 hard to operate
Original Message   Jan 13, 2011 1:09 pm
I have a 2004 Ariens 926DLE with the 9hp engine. I think it ran very well in 04 - 07 but about in 08 I noticed that I had to constantly keep lifting up on the handlebars to adequately blow snow. I seem to be always pulling up before moving forward; and if I don't the front end seems to ride up and snow just oozes out the chute. I find the Ariens is a lot more tireing then my older and smaller Honda HS80. I set the skids almost down the ground thinking it might be this, but with no change. I this just the way an Ariens runs?
Replies: 1 - 3 of 3View as Outline
hirschallan


If it aint broke don't fix it !!


Location: Northern Hills of NY
Joined: Aug 25, 2005
Points: 327

Re: Ariens 926 hard to operate
Reply #1   Jan 13, 2011 1:49 pm
BALR1415 wrote:
I have a 2004 Ariens 926DLE with the 9hp engine. I think it ran very well in 04 - 07 but about in 08 I noticed that I had to constantly keep lifting up on the handlebars to adequately blow snow. I seem to be always pulling up before moving forward; and if I don't the front end seems to ride up and snow just oozes out the chute. I find the Ariens is a lot more tireing then my older and smaller Honda HS80. I set the skids almost down the ground thinking it might be this, but with no change. I this just the way an Ariens runs?


Something tells me that your impeller belt may be slipping and not taking in the snow at a good rate thereby causing your bucket to ride up.

BALR1415


Location: Northern Worcester County MA
Joined: Jan 13, 2011
Points: 9

Re: Ariens 926 hard to operate
Reply #2   Jan 20, 2011 8:49 am
I checked the belts, and the attachment belt was loose. And it also has about an inch long chunk missing on the inside.

I am on my way today to get a replacement belt. The manual looks sort of clear on how to replace this belt , but a video or other tips would help since I am not the best for this sort of stuff.

trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Ariens 926 hard to operate
Reply #3   Jan 20, 2011 9:18 am
  The belt might just slip in but on some there is a pinch on the lower right as you look into the lower belt area facing the engine.  On machines that have the pinch you have to undo the top bucket bolts and tilt the bucket forward.  Put a support behind the handlebars.

  I'm still getting used to the Honda HS828 track but in the last storm it was pretty easy to use in middle bucket mode and I felt lest worked over than usual after an hour of clearing. 

   If that belt was the problem then you'll notice a difference.  The snow has to be gotten out of the front quickly to lessen front lifting.  You can lower your speed by adjusting the friction disk or feather the clutch to slow down in tougher spots.  Some Ariens machines are .9mph in first  You can check that by running for 15 seconds than walking off the distance a few times then do the math for MPH.  Setting a bit slower helps out.

Replies: 1 - 3 of 3View as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42