Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens eating belts

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
brjl


Joined: Jan 2, 2009
Points: 23

Ariens eating belts
Original Message   Dec 28, 2010 10:36 am
Ariens 11528DLE

I purchased this sno blower two years ago and I am about ready to install my third auger belt. Anyone else having this problem?

Thought I was buying top of the line, my fathers vintage 1970's Ariens refuses to die and is still throwing snow like new. Very frustrated. Cold weather and no garage is no time to be replacing belts.

Brian

Replies: 11 - 20 of 20Next page of topicsPreviousAllView as Outline
brjl


Joined: Jan 2, 2009
Points: 23

Re: Ariens eating belts
Reply #11   Dec 28, 2010 4:50 pm
Thanks for your  help, I am going to purchase an authentic Ariens belt in the next few days and checking the alignment of the pullys.

Thanks again

Brian

This message was modified Dec 28, 2010 by brjl
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Ariens eating belts
Reply #12   Dec 28, 2010 5:03 pm
>>>The second belt was a belt from a parts store.

Auto belts at a parts place are made different than OPE belts you would get at a hardware store.  The OPE belts have a strengthened backing for OPE use.  Hardware stores often carry a couple of types of different quality in common sizes.   I have never had a problem with the lower cost belts and occasionally use the more expensive belts both of which are less expensive than a manf's belt.    One Murray belt was $42 which was $9 at the hardware store. 

Get the part number of your belt at the Ariens site and google it.  You'll get hits for various belt places and many list the size.  All belts I get for Ariens machines are hardware store belts and work fine.

This message was modified Dec 28, 2010 by trouts2
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Ariens eating belts
Reply #13   Dec 28, 2010 5:08 pm
I buy all my belts at Advanced Auto.  They sell a line of OPE belts. They are pretty heavy duty and I've never had a problem with them.  They usually run about. $9.50 each.
brjl


Joined: Jan 2, 2009
Points: 23

Re: Ariens eating belts
Reply #14   Dec 30, 2010 9:19 am
I relaced the belt with a OEM belt, seem to be about 1 inch shorter and much beefier than the last belt. All pullys are aligned and everything seems normal. After this winter is over, I will measure this belt with the old one I took out to see if it is stretched. Thanks again for the help.

Brian

bus708


Location: Maryland
Joined: Jul 24, 2010
Points: 321

Re: Ariens eating belts
Reply #15   Jan 1, 2011 10:38 pm
Check  your auger drive for binding. Also check your idle pully for binding. Both should turn free by hand. Make sure you are adjusting it correctly. If you idle pully bolt is loose your belt will go out of adjustment
This message was modified Jan 1, 2011 by bus708
PartsMan


Joined: Jan 28, 2011
Points: 7

Re: Ariens eating belts
Reply #16   Jan 29, 2011 10:50 pm
I had the same problem and I came to the conclusion that the engine is just so powerful that when the auger gets full of snow instead of the engine slowing down it keeps turning full speed and slightly slips on the belt and burns it.

Check if you have some black soot under the belt cover and around the inside. Also a belt that is all cracked up inside is overheating.

I have all the OEM sizes Ariens belts on my site at   http://www.c-equipment.com/snowblower-ariens-belts.html
This message was modified Jan 29, 2011 by PartsMan
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Ariens eating belts
Reply #17   Jan 29, 2011 10:58 pm
Partsman, your a running advertisement not a contributor. Dennis, what are the rules on advertisers? Are we going to have to read ads in all posts?
aa335


Joined: Nov 29, 2008
Points: 2434

Re: Ariens eating belts
Reply #18   Jan 30, 2011 4:08 am
It's quite easy to ignore the advertisement.  Quite subtle and not too annoying.
mkd55


Location: wisconsin
Joined: Dec 16, 2005
Points: 155

Re: Ariens eating belts
Reply #19   Jan 30, 2011 10:46 am
brjl! eating up belts should not be the norm! i would check the pulleys for allignment,burrs,dings,and free movement.i had a belt go on my cub cadet at 200 hrs of service.first i thought it was normal and figured i'd have to replace it every 200 hrs.i bought a new cub cadet belt for it and it didn't last a month of mowing grass.one of the two directional pulleys under the front end had the bearings going out and was so bound up it was putting extra load on the belt.the bearings finally launched and the bearing hub seperated from the pulley. replaced both pulleys and  not 3 hrs later the replacement belt seperated in half. if the belts are freyed it tells you one thing and if the belt is an abrupt shear it tells you something else.in my case the second belt broke in an abrupt shear just like pulling a piece of licorice in half.it had no free movement on the frozen pulley and the engine simply pulled the belt in half.
This message was modified Jan 30, 2011 by mkd55
brjl


Joined: Jan 2, 2009
Points: 23

Re: Ariens eating belts
Reply #20   Jan 30, 2011 5:24 pm
This machine has been looked at by two different dealers, and I have checked everything that I could, all looks normal. I know people who have the same machine with no problems. I am thinking about selling it and getting a Toro.
Replies: 11 - 20 of 20Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42