Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions |
|
aschmeer
Joined: Dec 27, 2010
Points: 2
|
|
How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Original Message Dec 27, 2010 3:06 pm |
|
Hello all, first post here...
My wife asked me to snowblow out out elderly neighbor...
Unfortunatly, not knowing there was a mat at the bottom of her stairs, my snowblower sucked it up and is now jammed in the impeller area. I have a Toro Power Max 826 LE Model #38620.
The mat is, of course, not a some light weight mat... no, no... it is one made out of old tires and "sewn" together with rather thick wire. I could cut it out, but would take an enormous amount of time and energy. I was trying to find out how easy it would be to partly dismantle the impeller... and how to do that?
Any help would be appreciated!!!
|
daniel
Location: NY
Joined: Oct 21, 2010
Points: 48
|
|
Re: How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Reply #2 Dec 28, 2010 9:33 am |
|
Ouch, no good deed goes unpunished. Good Luck, think you're just going to have to snip snip a whole lot. -Dan
Toro 826 OXE Snowblower, Echo PB-500 backpack blower, Toro 22" high wheel recycler mower, Jeep Wrangler JK Unlimited 6 spd :)
|
mml4
Snow is good, Deep snow is better!
Joined: Dec 31, 2003
Points: 544
|
|
Re: How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Reply #3 Dec 28, 2010 9:35 am |
|
Ouch, no good deed goes unpunished. Good Luck, think you're just going to have to snip snip a whole lot. -Dan X2
Marc
SnapperV210P,Toro22177,TroyBilt42010Snowthrower,Craftsman Shredder,American Turbo Pressure Washer HondaGX200,Stihl011Saw,EchoPas260Trimmer Edger,EchoPB602Blower,EchoHCR150Hedge Clipper
|
bmwe0692
"Have a great and glorious day"
Location: Iowa
Joined: Dec 4, 2004
Points: 79
|
|
Re: How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Reply #4 Dec 28, 2010 9:07 pm |
|
If you can borrow a small set of bolt cutters, try to cut any wire you can reach. A vise grip snapped on to the end of the wire,pull out what you can,cut it off. Turn impellor repeat-repeat, till all is gone. Two hours and I'm good to go. No more mats at my house!!! T.J>
Put it where the Big iron wheel runs!!!
|
aschmeer
Joined: Dec 27, 2010
Points: 2
|
|
Re: How to unclog Toro Power Max 826 LE Model #38620 impeller blades
Reply #6 Jan 4, 2011 7:04 pm |
|
Ouch, no good deed goes unpunished. Good Luck, think you're just going to have to snip snip a whole lot. -Dan You got that right... Well I appreciate everyone's responses. Waited for a nice, rather warm day and went to work with my razor knife and bolt cutters. Took about 2 hours, but I got the mat out... although it is useless as a mat now Thanks again!!!
|
|
|