Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Preface: I've have has a HS520. Due to space contraints, etc - I'm not looking at 2 stage. Single stage for the most part is a perfect fit just short of....living on the right side and the plows only plow to the right so I cam constantly getting plowed in... Throw is fine already on the HS520. I was only curios does the 421/221 or even any current models on the market may have a bit more bite on the EOD/overnight plowed snow...

U did say that I needed to have the *trips*.

I've been busy collecting all the mint HS621 that is remaining stateside.
Well, out went the 520 and in came another minty mint 621. This time it was even in better condition that the last one. There is a very small *dent* on the inside of the bucket and a scratch/scar on the chute but it's nontheless a easy 8.5/10. No rust at all, bucket edges are extremely clean, bolts are nice and clean....and I got it at a steal of a price. Included was a brand new OEM belt, OEM scraper, *honda branded* plug still all in their Honda baggies and a 8.5/10 unit WITH a leaky hose (I've yet to determine the fault as i just came back with it) but the long and short of it was that with the fuel in the tank, it continuously leaks/drips the fuel out until the tank is dry.

I was just looking for a parts machine and came across this HS621....price was right and it got down even cheaper after we discovered the leaking gas issue...
Owner was meticulous, told me how he ran the carb dry, oiled the bolts after every season, sprayed it down with silicone, etc and it shows in the condition...

And this time I did check and made sure the auger was purfect....only small dent that you notice when you run your hand on the backside of the bucket..

In the meantime, I'm in the midst of a R&R of the other one with screws in one box, parts on another, stuff hung and getting ready to be painted, etc.

I went ahead and added new auger augers to my order just because....

I'm so knee deep into it and as silly as it's sounds, I may just want to strip off all the old good decals and put new fresh ones on.

The last thing remaining is whether I spend the big $$$ for a stainless scraper.....

Just some pics for the hell of it....

AA, I GET what you say about the auger stiffness now, as how the rubber sits entirely on the auger paddle frame, as opposed to the lattes where there may be some flex...

SORRRRRY in advance, I will RESIZE THEM LATER ON...

I told you so, if you sell one off, you'll pick up another.  That's just how SAS (snowblower acquisition syndrome) works.    Anyone else has this affliction?

I know you're pretty knee deep in this stuff, but at least it's cheaper than some other things you can get into.  Like gambling or karting.

On the stainless steel scraper bar, is that a custom fabrication or you can readily purchase?

The SS mod....I've kept you in mind

I hit up my local shop that I always use....but to have a exact replica made in SS, it was too costly if not extremely costly.
When is anything with the word custom not costly...

I'm planning to try a couple of other shops in my contact list but I suppose it may be the same or not...
Different fabrication techniques, etc come into play into costing of the final product as well

The SS mod....I've kept you in mind

I hit up my local shop that I always use....but to have a exact replica made in SS, it was too costly if not extremely costly.
When is anything with the word custom not costly...

I'm planning to try a couple of other shops in my contact list but I suppose it may be the same or not...
Different fabrication techniques, etc come into play into costing of the final product as well

Thanks for thinking of me.  I had consider the metal scraper bar a while back when I first acquired the machine.  The plastic ones wear down so fast on concrete surfaces.

Let me know what the cost would be for a stainless steel one.  An exact SS replica sounds awesome.  I'd probably join you for a group buy.  :)  Have you consider titanium, like the ones on knee pucks?  Throw some sparks while snowblowing. 

So what's your plan now that you have two HS621?  Flip one of them for a HS35?

I really need to start putting #'s down on paper or else I will get myself in trouble like I always do with side hobbys.

I think I'm going to do a mild RR on the other 621 and just give it to my sister.

The scraper bar from my CNC shop was very expensive...
It cost MORE than what I paid for the 2nd 621.