Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I'm at a loss. I have a Paramount GB350  leaf blower with a 2 cycle Mitubishi engine. I need a priming bulb. My old one is so old it has gotten hard. Does anyone know ware i can get a new one or a new carb assembly?  I cant find any serial # on the engine or any info on the engine or Parmount blowers

The bulb, is it on the carb or mounted on the blower? If the carb has the primer bulb mounted to it, I believe it is a NIKKI carb, if it is mounted on the blower case it could be about anything... The gb350 was made about 1988, and is a fine unit even by today's standards and well worth fixing... Post a close up photo, one of the whole unit, and one of the primer bulb/carb area.... Then we can figure out what you need. Friiy

THE CARB IS A  NIKKI 6505.  I CANT FIND ANYTHING ABOUT THE ENGINE, THE CLOSEST INFO I FOUND AS A KAWASAKI T200. I THINK IT IS THE SAME ENGINE. THE PRIMING BULB IS ON THE TANK.  I REMOVED THE CARB AND CANT GET ANY FUEL TO PASS THROUGH THE FUEL LINE, I TOOK IT APART AND SOAKED IT IN MY ZEPP TANK FOR 3 DAYS BUT STILL NOTHING . I WANT TO REPLACE THE CARB,FUEL TANK AND PRIMING BULB BUT CANT FIND ANY LEADS TO BUY THEM 

That nikki carb/ engine I believe was used on the Toro line of line trimmers of the same year. (about 5 year span) .....  and the tank mounted primer bulb....

The carb is most likely good ,   it just needs new Diaphrams/ gaskets and maybe a needle...   It you take the primer button apart do not loose the parts inside (plastic $#%* and foam and such)....

I will do a little research and see what I can find,  try to take a picture So I can better follow up...

Friiy

Take a look at these links : http://jackssmallengines.com/help.cfm#AssemblyPartsSearch|model_d9MoRLNeA8MAkFKWRhWEsQ==|assembly_as7zA/ZBtriCb2MVUeSFeA==|brand_dSFVgwdT0oMPfsKWPzzq7A== and try this one also: http://jackssmallengines.com/help.cfm#AssemblyPartsSearch|model_d9MoRLNeA8MAkFKWRhWEsQ==|assembly_TinPoVGw2Crw2axBzpV5Xw==|brand_dSFVgwdT0oMPfsKWPzzq7A== The repair parts are typical, the tank may be different but the fuel pipe assy should be the same.... The carb as a whole will not work.... (body jet size, needle size, throat are made for different engine cc and rpm) but the diaphragms / gaskets and needle should be the same... Friiy

Try this link :

http://jackssmallengines.com/help.cfm#AssemblyPartsSearch|model_d9MoRLNeA8MAkFKWRhWEsQ==|assembly_TinPoVGw2Crw2axBzpV5Xw==|brand_dSFVgwdT0oMPfsKWPzzq7A==

and this one...

http://jackssmallengines.com/help.cfm#AssemblyPartsSearch|model_d9MoRLNeA8MAkFKWRhWEsQ==|assembly_as7zA/ZBtriCb2MVUeSFeA==|brand_dSFVgwdT0oMPfsKWPzzq7A==

I found these under Toro TC-3100 line trimmer,  1992 model....at Jacks small engines parts...There are others it this does not look right...

Sorry about the secound post, I am having problems with the Edit/post/link thing today...

Friiy

Friiy

Thanks  for the info. The toro loks very much the same. I cant see the bottom of that unit though. Mine has a drain valve or somthing on the bottom.I'm trying to get my pictures posted. I have them on flicker. I cant seem to get them to post. I will  post them as soon as I figure it out. Again thanks

likely the carb purge line, Hold down the lever and push the primmer till it pees.. There is a toro I am sure that has that.... Friiy

bus708 wrote:
If you're not having any luck with flickr, try imageshack.us  It's been very reliable.

These are pics of my carb.


I can't get flicker to post my pics. Please  copy and paste my url to see my pics.   http://www.flickr.com/photos/bus708/