Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Preface: I've have has a HS520. Due to space contraints, etc - I'm not looking at 2 stage. Single stage for the most part is a perfect fit just short of....living on the right side and the plows only plow to the right so I cam constantly getting plowed in... Throw is fine already on the HS520. I was only curios does the 421/221 or even any current models on the market may have a bit more bite on the EOD/overnight plowed snow...

I've got an LS 1013, and it's a great saw.

The blue machines are REALLY nice. If I had bought "new", I definitely would have gone with the YS928SJ. No shear-pins to deal with,,, joy-stick chute control,,, 12v starter (battery),,,,quiet as can be,,,a real little bulldozer.

AA - Still jonesying for a 621. You should have never pointed out the GC vs GX....
I kinda like the fact it's got a metal cover as well, I know, silly things

Let's run down a shortlist of things...

- Rebuild/New Carb - $60
- Scraper, Paddles, Belt - $125
- Plug - $7

Minimum - $200 vested repairs into it..
I'd rather replace the carb then rebuild at the cost vs. time ratio....

Do you have new paddles. I am VERY curious what the OEM New length is on this....so I have a reference point.....
Thx

chefwong wrote:
I can relate to how you feel.  There's common blood among connoissure/collectors.   :)  The 621 is a fine piece of machine.  Just want to ground you with some reality though, the HS520 and Toro 221Q being newer and optimized, throw snow further in most instances, except slush. 

I have new paddles not installed yet.  What measurement would you like me to make? 

Northeast territory. We get the wet stuff....
More TOOOORQUE .

You may need to eyeball it, but how much rubber do you have from the edge of the auger paddle to the auger support (as if the paddles are mounted on).


----

I feel like I'm on a time constraint. I either Source a 621 before this winter or I'm keeping the 520. While the 520 may sell well used, it sells even better *brand new*....

chefwong wrote:
Ok, I'll overlay on the auger and make the measurement this evening.  I'll put on the metric eyeglasses, unless you prefer fractions, then I have to stop by the optometrist first. 

Most people don't know what a 621 is.  Only people in the know go looking for a used 621.  You can easily sell the 520AS at a higher price than you could pick up a used 621.  Although mint condition 621, hard to come by, is usually well kept and maintained by people who know the value of it and are usually priced high.  You get what you pay for.

Hold on to your 520AS until mid winter, you get even better price then.

The Banghead Smiley is missing on this forum ;-)
I would need 6 of those to start this response....

I have a boatload of cedar that I need to finish indoors to store these puppys.
Can't build it straight outdoors cause due to temps, and proper application of finish coats, I need to do all this indoors.
That is something more like a 2 weekend outdoor project easily done outdoors and now I have to piecemeal it.....grrrrr

I don't see a problem here.  I'm sure you can come up with new equipment to make the job faster and better.  :)

You have a Festool shop vac, don't you?

Yeah. The beauty with that and the Kapex in a indoor setup...is 90%+ of the dust is captured.
I don't have the exact percentage but it is HUGE...

BUT, FWIW, it's not now loud as thunder Shopvac.
I feel like I have to baby the Festool.

The bigger regular $50 shopvacs are lounder, and has more  ballz, and I would not hesitate using those as a wet vac....

But the Festool lineup is a ~system~....

While on the topic of tools, previously was using Makita drills, went over to Panasonic drills (sleeper brand like the HS621) but I'm back over to the Makita's.....
Impacts, Drills.  All very balance. Don't really ever need more than 14.4...

Snap On for the track bollts. That thing has some serious torque that no others can compare.

You should have never pointed out the Kapex 120.  What a saw.

Ok, I'm not going to visit Festool website, ever again.  I'm just going to put up with loud as a turbine Shop Vac.