Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Preface: I've have has a HS520. Due to space contraints, etc - I'm not looking at 2 stage. Single stage for the most part is a perfect fit just short of....living on the right side and the plows only plow to the right so I cam constantly getting plowed in... Throw is fine already on the HS520. I was only curios does the 421/221 or even any current models on the market may have a bit more bite on the EOD/overnight plowed snow...

It was kinda weird...I go there to inspect it and I was like can I crank this up ...
He reaches for the extension cord and I was like, no, let's pull the cord.
He does like 6-10 ~wimpy pulls~ and I was like let me try it. Give it a ~good pull~ and it starts right up...

Then he goes on to tells me he has always used the electric start .

I obligly ask if he minds if I drain the oil outside his driveway ....I  brought my small oil vac.
He says sure, no problem and he actually did it for me on the spot.....by tipping the unit over and pouring the oil backwards out of the fill hole.
I asked is this how you normally do it....there is a drain bolt right below, and he told me this was how he has always changed the oil.

So the seller was not the most mechanical, but yes, I thought the condition was in really great shape.....

Except for what appears to be a bent auger, which I did not pick up on till I was looking at the pics.
Hopefully, someone with a 621 can chime in and confirm wheter one side is slight tweaked or fully straight....

That center part should be flat across both sides.  Looks like both sides were bent.

However, it should look like this.

http://cgi.ebay.com/Honda-HS621-HS-621-Snowthrower-Snow-Thrower-Auger-NEW-/250611539091?pt=LH_DefaultDomain_0&hash=item3a599c9c93

As long as the gap between the bucket and rubber is small, it should not affect the function.   Try spinning under engine power to see if auger vibrate and out of balance.

If it bothers you, return your new paddle set and consider buying that auger assembly on ebay, it comes with the new rubbers.  So essentially,  $160 for the metal auger.

My auger is bent too, slightly on one side.  I'd probably consider buying that auger assembly the next time I need new rubbers.  But it's so miniscule, I might just overlook it.

I do have ~issues~. Especially with any motor equipment.....I'll go to far as replace exterior moulding on my cars cause the sun has aged it and while trim products make them look good....it's just not as good as fresh. I think I may just spring for the augers but It's more like $200 extra when you factor in the shipping.

Grrrrr.....in the pitch of night and with the flashlight making sure the augers spun, and bearing that it looked so mint and rust free (just short of the marks on the bucket), I thought I made out pretty well - considering others in my area were asking $450 with questionable body conditions..

Buy another one, switch the augers, then resell it :)

chefwong wrote:
I know what you're saying.  Replacing that moulding would not work for me.  New molding would stand out looking so good, that the rest of the car looks crappy.  $200 dollars later on car detailing and I'm still not satisfied.  I'd go out and buy a whole new car, moulding and all.  .  Until the wife says, "NO, YOU'RE NOT.  IF you have been putting up with my imperfections the last several years, you can hold out on a new car just as long".  Hehehe, my wife didn't actually say that.  I'm just dramatizing.

Get the new auger and put everything else behind you.  You got lucky finding that 621 in such a nice condition.  I wouldn't go through the trouble of finding another unit to swap parts with, unless you have time and patience.

New Auger ordered.

Now can someone please help me explain Why-TF I have 3 snowblowers in my possession....

chefwong wrote:

You have snowblower OCD!  

chefwong wrote:
You are suffering from SAS

Snowblower Acquisition Syndrome

It comes in three's.  That's just the way it is.  Don't sell off anything or you'll start the cycle all over again.

chefwong wrote:
This is your original posting. Kind of funny looking at it now...LOL.

chefwong wrote:
Hah, top that. 

What's the first step to recovery?