Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Yep, that's it aa335. I don't think the bucket was touching the ground, and in retrospect, I'm quite sure it wasn't. I was just looking at the tracks, and only the portion of track under the drive-wheels was contacting the floor. From there, it was simply a matter of rotating the machine left or right. No heavy lifting at all.

For clarity's sake, I should also point out that the 1-finger method, was simply for rotating the machine. It had nothing to do with displacing the machine to another area..

drifter,

While we're on the topic of moving up and down the bucket in 3 different positions, I just remembered something about the HS928TCD that the bare bones 928TA does not have.  It is the hydraulic assist and lever to actuate the bucket up and down.  The US version, non - TCD, have the pedal instead of the lever.  While it does the job, I would prefer a lever because trying to step on that pedal while you're on ice covered ground puts you at risking of slipping. 

If the salesman hasn't already demonstrated this feature, it may be worthwhile to check it out to see whether it's worth the additional cost of the TCD models.

You're already seriously considering the Honda, a little more $ for the TCD may be better in the long run.

aa335 wrote:

aa335: Which position do find yourself using most often? I have not had the opportunity to use my new toy yet and am curious about the transport mode position. Seems like this allows the operator the choice of having the scrapper bar make contact with the pavment or having it slightly off the pavement.

I rarely use the scraper setting (bucket angled down, lots of weight).  It's too much strain on the snowblower.  If I do use it, I go very slow give the auger plenty of time to chew the ice up. 

I use the normal (middle) setting for clearing snow, and the transport setting (bucket up) at the end of the row for making tight 90 and 180 / u-turns.  I do use the pedals a lot to go from these two settings.   Hence, the a hydraulic lift assist and lever would be much more convenient over the manual lift and pedal.

I'm still so new to these machines that I didn't realize there were different methods for raising the augers. I'll check-out that hydraulic system when I go back.

On a side-note; I'm checking out the "used" market today, and I just missed an 11-32 for $2000. I don't know how old it was, but it looked new (newly repainted).

I was surprised to see that for the most part, 2 year old and less HS928's, are going for $3200. plus.  I'll keep looking, but that 1 year-old HS11-32 which the dealer is receiving, is starting to look attractive at $3500.

FrankMA wrote:

I had a 928TAS and believe me there is no way you can move it with one finger unless you are "Andre the Giant". Yes you can freewheel the tracks as has been stated but you are still moving 200+ lbs. on tracks. The lever to tilt the bucket is a cool feature and it actually has 3 positions way up like 2 inches high and then near the ground and then scraping the ground. That's how mine was setup anyway. Also a cool feature as the machine tends to stay put and not ride up.

Guys, I'm starting to think there might be a "blue" snow thrower in my driveway shortly.

I dunno,,,, that Yamaha YS928J sure is starting to look VERY attractive to me. I really liked how quiet this machine was. It has 12vdc start (battery), the engine shroud which keeps noise levels down, serrated scraper-bar, teflon-lined chute and impeller housing, fuel gauge(need to verify), drift-cutter, auto-choke, and electronic chute control.

http://www.yamaha-motor.ca/products/products.php?model=3537&section=td&group=G#contentTop

drifter wrote:

Supposed to be a great machine but expensive. If you do buy one take pics of it. :)

Will do Steve,

I have to go back and take a closer look at both,,, the Honda and the Yamaha. They're both the same price when you choose the electric-start models.

I want to actually operate the bucket-lift mechanisms, and I want to move both machines around. Small detail; I'm not certain the Yammy has hand-warmers.

drifter wrote:

drifter: That is one impressive machine! Looks very up to any snow clearing task you could possibly throiw at it - at 373 lbs. it's a real beast. Please keep us posted and don't forget pictures when (not if) you buy it and get it home.