Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I have a Ariens 924108. My snow blower will not blow slush. I see other folks bragging about it. I also see some folks using there snowblower as as pump throwing water from the house. When I go into slushy stuff all It does is vomit out of  my shoot 3 inches. Is there something wrong? It blows snow poor too. 10 feet of heavy wet snow.20 feet of regular snow. My blower has  a 8 hp Techumseh. This snow blower is rated to throw snow 50 feet . What can I do to improve performance.

I don't think a bigger pully on my engine will do me any good. Yes I will gain speed but will loose torque. That will bog down my engine. I need a bigger engine for that.I do not know how good those rubber incerts really help. I wasn't impressed with the guy on u tube. He didn't even show them mounted in his blower. I don't here of anyone else eather . That thing can throw your impeller out of ballance.

        I believe the thower would not be affected by the wiper impeller kit,  The unit does not operate throwing snow in a state of balance, every bite of snow thrown is not even..  Also the kit pieces are all the same (weight)  for each blade-- Dynamic  and static,  the balance should be the same as a unmodified blower impeller.

      One large problem with thowing slush is the wet snow is easly pressed into the gap between the impeller and housing..  This gap with wet / lubed snow allows the slush to loose speed and slip past the blades (lost efficiancy and waste of slush speed for ejection)..  The kits sold take away any gap and wipe the housing clean with every stroke.

    I highly recommend the kits,  I made one for a friend of mine who has a cabin.....I made the kit out of some rubber conveyor belt  material and pop rivets,  You can use bolts or screws if you wish, the the rubber is not under much load,  I think i took me 2 hours.. and  5 bucks

Good Luck,

Friiy 

I'm seriously considering the impeller kit for my blower. Not that I have any complaints so far. I haven't had to blow any slush yet though. For what it costs, it would be a neat experiment. You can't argue with the logic.

Guys ... I have only seen a few of these kits installed and working in front of me. I have seen a remarkable improvement in throwing wet snow... I consider wet snow lubricated snow, meaning it slides to where it wants to go.... The wet snow under pressure from rotating impeller is slung to the outside of the housing impeller, this wet "lubricated snow" is jammed to the edge where it slows down with the friction of the housing and easily slips between the impeller and housing .. This slurry just rotates not being ejected from the chute... The added pressure of the spinning impeller slams the wet snow flat into housing allowing the impeller blade to slide past without ejecting it... If you don't believe this happens, Try taking a 7-11 slurpie and cutting a hole in the bottom of the cup the same size as the gap of your impeller / housing .. The slurpie may stay in the cup static for awhile, then try spinning the slurpie at the end of your arm (like a water pail) and tell me how much you still have in the cup.. The slow spinning slush on the outside resembles the margarita in a blender, the outside spins slower than the stuff next to the blade... The impeller kit cleans the housing of all snow by wiping the sides clean with zero clearance with every blade pass.. The velocity of the wet snow is the same as the impeller blade tip speed... the snow is easily injected at those speeds, the auger has a easier time throwing snow to the impeller housing because there is less/ no slurry in the housing... -Friiy

I haven't put the Clarence kit on mine yet.   I have it but will install when the warranty is up.    I did a pulley upgrade that gave a substantial boost to the throwing distance.  I didn't get a real chance to test out in the slush last season.  It was a bad "no" snow year in the Pacific Northwest.

Second picture shows stick pulley.  I had to put a larger Husky belt cover on as well since new larger pulley rubbed somewhat.