Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Diagnosing a (new to me) 2-stoke engine for trouble

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
Underdog


Joined: Oct 18, 2008
Points: 332

Diagnosing a (new to me) 2-stoke engine for trouble
Original Message   Mar 16, 2010 9:22 am
How do you diagnose a 2-stroke to find out if someone ran straight gas through the engine and wrecked it?

I found a Toro snow commander snow thrower (see photo). I've never used a toro single stage so I thought I would snatch it up. The previous owner said that it did not run. Apparently it ran last year but not very well. Looks like it sat out in the rain most of its life. That's all I have to go on. 

At 24" the blower is wide for a single stage and very heavy (over 100 lbs).  The 7hp engine appears to be the same InTek 2-stroke as the Toro 3650 and 2450.  I noticed that it does have an electric start feature.

Now that the blower is sitting in the garage, I realize how large it is. Think "single stage monster."  A very odd beast,  a mass of red plastic.  Toro only sold these (model 38602) blowers for a few years (2001, 2002, 2003, ?) with a list price of $960 US. There was a Toro recall in 2006 for 2001 and 2002 models. This one is a 2003 model.  I don't think they were very big sellers (expensive, hard to handle, too many parts).

I don't have any experience with 2-strokes so this is a new adventure for me. Is there an easy way to determine if someone ran the engine with regular unmixed gas and ruined the engine? Would I notice anything when pulling the starter cord?  I thought I try to rule that out first if there was an easy way to do so. 

This message was modified Mar 16, 2010 by Underdog


Replies: 28 - 37 of 45Next page of topicsPreviousNextNext page of topicsAllView as Outline
superbuick


Joined: Feb 23, 2009
Points: 138

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #28   Mar 19, 2010 11:14 am
I hear what you're saying Borat, and understand the reservation, but with a good oil they can, will, and actually DO run better with a leaner mixture (as you mentioned, more oil means less gas, which means a rich mixture makes it run lean and vice versa). The added carbon buildup can cause alot of hassles and in addition, not all of the extra oil will be burnt, resulting in more goo/mess. I've been using Opti-2 at about 80:1-100:1 with no problems for 3 years now in EVERYTHING (trimmer, blower, snowblowers, lawn boys, even my RC Boat)
borat


Joined: Nov 10, 2007
Points: 2692

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #29   Mar 19, 2010 12:16 pm
superbuick wrote:
I hear what you're saying Borat, and understand the reservation, but with a good oil they can, will, and actually DO run better with a leaner mixture (as you mentioned, more oil means less gas, which means a rich mixture makes it run lean and vice versa). The added carbon buildup can cause alot of hassles and in addition, not all of the extra oil will be burnt, resulting in more goo/mess. I've been using Opti-2 at about 80:1-100:1 with no problems for 3 years now in EVERYTHING (trimmer, blower, snowblowers, lawn boys, even my RC Boat)

Yeah, lots of people like to run a lean oil to fuel mix   I mix 100:1 for my newer liquid cooled outboards but like to keep the oil ratio a bit higher in my air cooled engines.   I've been doing that forever.  The Dead Sea was  just getting sick when I started.  

I run a bit of Seafoam through them occasionally and I've been pretty lucky regarding carbon build up.  I'd venture to say that newer two cycle engines would be more tolerant to a thinner oil mix particularly with the better quality of newer oil formulas and synthetics.  However, I'd stay on the rich side for anything that's ten to twenty years old or older.   I guess it's whatever an individual's  comfort level is.   For me, having the convenience of one fuel mix with a slightly higher oil content gives me confidence that the engine's lubrication needs are being met.  
Underdog


Joined: Oct 18, 2008
Points: 332

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #30   Mar 19, 2010 9:38 pm
The idea oil packaged in single use quantities is sure appealing. From the advertising it is difficult to know what ratio the pre-mixed product are..

This message was modified Mar 22, 2010 by Underdog


friiy


Location: Las Vegas, The Desert
Joined: Apr 12, 2008
Points: 600

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #31   Mar 19, 2010 10:25 pm
I agree on alot of what you guys are saying about oils.....  All 2 stokes require the same lube requirements,  oil are of diffrent quality...

       Opti oil 2 (I remember the original)...  100:1 mix Is a GREAT oil...  The problem is sloppy mixing of fuel...  If you have a guy working for you that does not check the ratio of the oil to gas as he mixes it, ( mixing too little oil or too  much fuel).. you may have mixed fuel that falls short of the 2 stoke engine's needs..  at about 1.7 oz per gallon,  a small error gan make a the fuel mix around 140:1... 

When Opti oil was big news 20 years ago,  I went to a few oil  shows and asked some questions ...  Most oil suppliers told me they could / have made their oils 100:1 or even 200:1 (some using Murcury metal) , but the consumer will not follow directions closely enough to protect the equipment, and packaging for one gallon mix containers is wasteful...  Hence, a 40:1 or 50:1 ratio is widly accepted as OPE norm and hard to screw up for the end consumer.

-Friiy

 

Underdog


Joined: Oct 18, 2008
Points: 332

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #32   Mar 20, 2010 10:07 am
The R-tek is reading 4138 on the tachometer.  I took several reading and they ranged from a high of 4138 down to 4128 rpm.  I measure the rpms on the shaft that comes out this side of the engine and drives the pulley  



borat


Joined: Nov 10, 2007
Points: 2692

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #33   Mar 20, 2010 10:51 am
At those kind of engine speeds, with proper lubrication, that engine should last forever.  I've got 35 year old, vintage, two stroke Yamaha twin cylinder motorcycles that have the rev limiter set at 10,000 rpm.  They can spin up to that speed without hesitation and being as old as they are, that should be a testament to their durability. 

The small individual oil bottles might be appealing but you might want to compare the price of their contents to that of a quart or a gallon of high quality two stroke oil.  For your application, having one two cycle machine, it might be worth while using the small bottles.  However, a small plastic measuring cup or calibrated turkey baster will readily measure your oil requirements.  Many two stroke oil bottles have a mixing scale printed on the rear label.  It's handy if the quantities they have printed match your mixing needs.  Otherwise, you'll still have to do some converting.  For those with multiple mix requirements, a custom made chart would be handy. 

Now that you have your carburetor sorted out, I recommend you pull the muffler off for an inspection and cleaning if necessary.  Some two strokes have a fine spark arrester screen in them that tend to clog up over time.  It's unlikely that there would be a need for one on a snow thrower but you might want to take a look nonetheless.   I know you had your machine running nicely already so, the exhaust is probably fine.  After a period of storage, you never know what what take up residence in a muffler.  

Several years ago I had left my old Suzuki ATV at camp unused for several weeks.  When I went to fire it up, it was reluctant to start.  Very unusual for this machine.  After a  minute or so of intermittent cranking at full choke and full throttle, the machine began to occasionally pop.  I cranked it over for a good ten seconds straight with it popping with regularity.  Suddenly there was this big "kaboom" and the engine started.   When the blast occurred, I saw something flying out of the back of the machine, out the garage door and onto the ground.  It was a mouse nest with three half grown mice rudely scattered about in the driveway!  

I'm assuming that the explosion was caused by raw gasoline accumulating in the header pipe and being ignited by flames from one of the engine pops.  Either way, it certainly cleared the exhaust system.    
Underdog


Joined: Oct 18, 2008
Points: 332

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #34   Mar 20, 2010 1:21 pm
I will check the muffler. Its easy enough to do. In fact everything seems easier to do with this motor. I'm still withholding judgement until the snow comes. But it is reassuring to hear of the longevity of some of these motors.

Is a measurement of RPMs at the output shaft representative of the engine rpms? Is there gear reduction that would create a difference between the two (engine/shaft) as there is on the Yamaha 4-stroke snowblower?

This message was modified Mar 20, 2010 by Underdog


borat


Joined: Nov 10, 2007
Points: 2692

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #35   Mar 20, 2010 5:18 pm
The output shaft from the engine should be the end of the crank shaft.  Accordingly, that's a good place to measure the engine rpm.  I usually use an electronic tach .   With those, you just wrap a wire around the spark plug lead and it reads engine speed.   Don't know anything about gear reducers on the four stroke Yamahas.  Never been exposed to one.
superbuick


Joined: Feb 23, 2009
Points: 138

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #36   Mar 20, 2010 6:04 pm
Here's a trick for cleaning the carbon out of a muffler:

Remove the muffler, place it on a hot charcoal (or even gas stove) and heat it to the highest possible setting for about 15 minutes.  Any carbon inside will turn basically to dust and you can simply tap the muffler lightly and watch it fall out.  Works great on old Lawn Boys which used to run at 16:1 and 32:1 back when oil quality was mediocre at best.

The motor will have more than enough grunt for just about any snow conditions.  I have one on my 2 stage PowerMax 726te and it will chew through nasty nasty snow that bogs down even much bigger 4 strokes.
Underdog


Joined: Oct 18, 2008
Points: 332

Re: Diagnosing a (new to me) 2-stoke engine for trouble
Reply #37   Mar 21, 2010 8:38 am
superbuick wrote:
Here's a trick for cleaning the carbon out of a muffler:

Remove the muffler, place it on a hot charcoal (or even gas stove) and heat it to the highest possible setting for about 15 minutes.  Any carbon inside will turn basically to dust and you can simply tap the muffler lightly and watch it fall out.  Works great on old Lawn Boys which used to run at 16:1 and 32:1 back when oil quality was mediocre at best.

The motor will have more than enough grunt for just about any snow conditions.  I have one on my 2 stage PowerMax 726te and it will chew through nasty nasty snow that bogs down even much bigger 4 strokes.

Will the high heat burn off the galvanized coating on the muffler and cause it to rust out?  Or is 15 minutes not enough time to do that kind of damage.  My charcoal grill can reach 500 degrees F without much trouble.

Replies: 28 - 37 of 45Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42