Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

We didn't have much snow, about 5 inches or so. But we had to get out so time to try out our new Toro 1028. I've gotta say compared to our Honda 928TAS the Toro feels really really light. My wife can't believe how light it feels and how easy it turns. She still has trouble with the quick chute but in a few storms she'll have it down pat. From the pics you can see how the machine is almost as big as she is. She was a little nervous using it but we are getting another 8 inches by tomorrow night she'll get more time using it.

Enjoy the pics. I hope they come out.

GtWtNorth wrote:

Thanks the house is great but needs a lot of work done on it. Some trees have to come down but cost too much. The Really Big one will cost us $3,000 to bring down. It's pine so the wood is worthless. My wife was taking pics that's why she didn't have her gloves on. It was actually very cold probably 10 degrees or so without the windchill factor. No handwarmers on the Toro. The snow had a slushy base but the top was light powder. The EOD was salty slush brownish and hard to throw. The Toro is tall for my wife for me it's just right.

aa335 wrote:

Thanks the house is pretty remote all things considered. But we are only about 5 miles from the Hospital. The Toro worked really well and did ok with the slush. The Honda 928TAS was such a bear to turn and you can see how small my wife is. She's still getting used to it but is not as nervous as before. We actually have 2 Honda Fits. I had a Honda Jazz when I was living overseas, same as the Fit but that one had the 1.3l engine. Great small car, does everything pretty well. I have some videos I might post on Youtube we'll see if not this storm then maybe the next one. Something with 20 inches of snow I hope.

Thanks Denis, The Toro works great and my wife is a real keeper as well.

How does the Honda Fit handle in the snow?  I'm looking for safe reliable transportation in the winter that I can also use for Home Depot errands.

Steve,

Great machine.  I'm glad you and your wife are enjoying it.

When I was shopping for a snowblower this past fall, I had narrowed my choices down to the Toro 828 and the Ariens 24 Platinum Deluxe.  One of the things I really liked about the Toro was its lightweight.  On paper, the toro 828 was 237 lbs while the Ariens Deluxe Platinum 24" was 224 lbs.  I ended up with the Ariens mainly because the smaller width enabled the unit to go through a very narrow path I have on the side of the garage.  The 828 was bit too wide to get through.  Now, however, I'm regretting my choice because of:

1. Although the Ariens is lighter than the toro on paper, it's way heavier to turn.  It even has auto traction control.  My guess is because the toro is longer, the weight is more well-balanced.
2. My Ariens has the snow series engine from Briggs. It's been backfiring when I shut it down.  I know the toro has the snow series max.  Any backfiring on that?

Joed,

I also have the Platinum 24, which I thoroughly enjoy (and hope you will too before long!).  When I'm done using it, I slowly reduce the throttle to low idle.  Frequently, the engine will give a quick backfire as I reduce the throttle, but it's really no big deal.  If I let it slow idle for 5 seconds or so, then shut it off, it will quit with no further backfiring.

Have you tried turning the machine off this way, or does yours backfire more cantankerously?

By the way, I used to own an early '70s vintage Ariens and had to replace the engine with a Tecumseh, which also backfired when I shut the thing down.  I just considered it part of the beast's personality... no harm done.  But I have to say that the new B&S engine runs smoothly and performs with a lot of oomph.

aa335 wrote:
The Fit is great in the snow, mainly because they use a very tall and narrow tire a 185/16 that's normally meant for 14" tires, so we cut right through the snow like a 4x4. We just run the stock tires with my Civic we ran Nokian snow tires the WRG2's. Awesome snow tire, but the Fit doesn't need them. Wer have 2 Fits because they are really that good. My wife gets around 38mpg and she's down to 32-33 with winter gas. My car have fewer miles so it's not broken in yet. I think I have 6,000 miles on mine. She has about 18K on hers. You can't go wrong with the Fit. Also I got mine under invoice! Tons of room in them amazing how big that little car is inside.

I spoke with a fella today about the backfiring and he suggested you turn the "crack screw" that controls the low idle and turn it up slightly. I think low idle is set at 1600 RPM. Try turning it up a bit.

joed wrote:

Hi joed, we really like the Toro and we did have a Honda 928 with tracks. We looked at Ariens but they were too hard for my wife to turn even with their limited slip differential. The Toro feels light and it is well balanced. The Skid steer makes all teh difference when manuevering it. The 828 is a good unit. Fron the pics you can see we need a bigger one. That said we did our driveway in an hour and 15 minutes. Not bad considering my wife is just learning, heck we both are. Our Toro has a B&S engine also. It's brand spanking new so no problems with it. It's loud but that's about it. If yours 's backfiring it must be running too rich. I'm sure it's just an adjustment. Post a pic of your 828 in action! I don't want to be teh only one posting pics.

I ended up getting the Ariens Platinum 24" Deluxe.  It' s heavy to turn, even with the auto traction control and the engine has been backfiring.  I really wish I had gotten the toro 828.

Too bad about the Ariens, have the dealer check it out as it should not be backfiring. It's a B&S engine, right. So they should get it working right.

The Ariens was a bear to turn even in the showroom and the Toro was a breeze. That's why we bought the Toro, it was so much easier for my wife to use. here are some YouTube links of my wife and I using the Toro 1028.

http://www.youtube.com/watch?v=rea9MWZwy18

http://www.youtube.com/watch?v=P4Dy-38GswU&feature=related

I have the scraper bar set at 1/8" since our driveway isn't totally flat. I tried it touching the driveway but it was too much work and it kept getting hung up on bumps. Now it's perfect.