Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

While on parts radar looking for things I came across "526025: 8.5-11.5 Belt Improvement Kit" for my snowblower. Does anyone know what this kit does and what it looks like? I'm wondering if it's worth trying to order.

I haven't noticed any auger slippage on my Ariens926. So why do I need I (arguing w/self). Probably don't. That drive slippage although rare and in short duration is Bo-gas. .

When I received the snowblower from my Dad in 2007 (he moved into a place where outside maintenence is taken care of and has no garage), lucky for me, I went over all the adjustments and lube in the manual. I noticed the auger belt was stretched but just moved the idler and readjusted the lever spring. After the second storm I had it, the belt was too stretched out to do anything (not sure how much he beat on it). I put a new belt on and haven't had a problem since.

I agree about the single belt, my previous (crappy) Home Depot Murrey only had one belt replaced over its 10 year life.

But... I'm also the type that has to tinker and improve. :-)

The Dual Belt Kit has two belts of the same size as my existing single and the pullies are beefy. I'm assuming it'll take a lot to stretch these, if at all.

My dealer and Snowmann both said that units built from 2007 on have this dual belt arrangement. I'm assuming Ariens is doing this so there will be very few complaints, if any, about adjusting or replacing auger belts.

iLikeOrange wrote:
I will be looking for one of these dual belt auger drive kits. The time when I get belt slippage is when I go through heavy wet snow, especially along the side of a street that gets plowed & has salt spread on it.

 I have been blowing snow for almost 40 years, and I can tell you that slush will cause auger belt destruction in a short time.

OHUQTU wrote:

"I can tell you that slush will cause auger belt destruction in a short time."... Do really think so? I've been using snow throwers for almost as long as you and I have found that a properly adjusted belt will pretty much stall the engine before it even slips. Keep the belt properly adjusted and it will handle anything you throw at it. I can see a dual belt system being more tolerant of mis-adjustment but I doubt that it's a necessary requirement. I know I haven't had any situations yet that made me wish I had a dual belt system.

I agree that proper belt adjustment is very important....but with a higher hp engine ( above 10 hp) and the standard 1/2" belt with a full load of slush puts a strain on the belt, and if its done for hrs,
 duel belts are the only way to go. Belts are the weak point in the system .

How much is the kit?

whitetail wrote:

Dual belts might prolong belt life to some degree but I doubt that it does anything to enhance performance. I'm not saying that it's not a nice feature. If I had it on my machine, I wouldn't be taking it off. On the other hand, I certainly will not pay to put a dual pulley/belt system on. Don't see a need for it. My machine goes for hours and a multiple tanks of fuel, pumping heavy wet snow without a hiccup. Last March 31st, we received 30" of heavy wet snow. My Simplicity burned close to three tanks of fuel, one right after the other clearing three big driveways as well as the EOD snow deposits. I was pretty much beat by the time I had finished the work but the Simplicity with it's single belt/pulley system was still moving snow as if it were brand new. So the question is, with that kind of performance, do we really need two pulleys and two belts?

I have an Ariens 11.5hp sno-thro that's a few years old.  The model number is 926002.  Is there any way to know if a dual auger belt kit will work on my machine?  I went to Ariens web site but couldn't find the answer there.

Ariens just e-mailed me 72600700 dual belt kit for my 2006 1128 LE.  IMHO, the unit lacks a creeper speed which makes removing heavy wet snow a problem with impeller and chute clogging and stretching out the single belt.  They now have this dual belt system that's supposed to be an improvement.  I have on order and will have to see.  I'm also considering a Clarence Impeller Kit that review rate highly for increasing throwing ability in wet snow.  I have an old simplicity that handles the wet snow better (10 hp 32") than this newer Ariens (11.5 hp, 28").  One reason is the creeper speed so the unit has time to process the wet snow, also has added 400 rpm kick in under heavier loads.  Ariens needs to pick it up a notch and take a lesson from simplicity. 

Rex1 wrote:

   What is "creeper speed"?  You seem to be refereing to some seperate gear or option other than 1st, the slowest selection of the standard friction disk and drive plate type. 

ALSO:

   You said the 1032 also had a 400 rpm kick.  How did that happen in the 1032?  What factory model number was that?