Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens 824 engine question

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
dok545


Joined: Dec 11, 2007
Points: 9

Ariens 824 engine question
Original Message   Dec 23, 2008 2:37 pm
I own a Ariens 824 model 932101. It has a Tecumseh 8 horse engine.  On the throttle it has a rabbit for high speed and a turtle for low. When I put the throttle at the low speed setting it shuts off. It runs fine at high or mid throttle. Is this normal or should it Idle at the lowest or turtle setting? Thanks, Glen from Minnesota   By the way, it's done this since new.
Replies: 2 - 9 of 9Next page of topicsPreviousAllView as Outline
dok545


Joined: Dec 11, 2007
Points: 9

Re: Ariens 824 engine question
Reply #2   Dec 23, 2008 3:10 pm
Thanks for the reply. It's not a big problem but seems to me it should idle at the lowest setting. I leave the key in all the time because it will shut off when I put it at the turtle setting. Why don't they put OFF on the lowest setting instead of turtle?   Not a big deal but just curious.  Thanks, Glen
friiy


Location: Las Vegas, The Desert
Joined: Apr 12, 2008
Points: 600

Re: Ariens 824 engine question
Reply #3   Dec 23, 2008 3:21 pm
It's suppose to idle at low speed,  It may be that your low speed jet is plugged on the carb..... Or the low speed throttle screw is backed out too far.. ( the screw  is located on the throttle plate or on a ear of carb casting near the throttle plate and shaft..

Friiy

dok545


Joined: Dec 11, 2007
Points: 9

Re: Ariens 824 engine question
Reply #4   Dec 23, 2008 4:58 pm
Thanks for the info. I'll take a look at the carb.  Like I said, it's been that way since brand new.  Glen
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: Ariens 824 engine question
Reply #5   Dec 23, 2008 5:21 pm

  If you go to the lowest turtle setting it >should< kill the engine.  At the base travel of low speed is a ground to the magneto. 

 

  When you come off high or mid range speeds into the low throttle range the engine will get slower and slower.  In the lowest area of the low range the throttle will eventually have no effect (not the very bottom) and have some slight travel with no effect until hitting the bottom of the travel – where the engine will cut out. 

 

  The reason for that is when the throttle travel gets low enough you hit the low RPM setting.  That is set with the jets and a screw on the top of the carb.  It prevents the throttle from restricting the gas so much that the engine shuts off.  It’s the min RPM setting and set by the screw.  Lowering the throttle more has no effect because the throttle is up against the screw.  Lowering more relaxes the throttle spring tension more but again has no effect because of the stop. 

 

  At this point further turtle has no effect.  Bottom turtle grounds the engine and is supposed to.

   

trouts2

 

 

dok545


Joined: Dec 11, 2007
Points: 9

Re: Ariens 824 engine question
Reply #6   Dec 23, 2008 5:31 pm
Thanks for the reply. If that's the case then everything is normal. Good to know. By the way, been getting snow every other day up here in Minnesota. Blower's been getting a work out this year. Snowed last night and another storm predicted tomorrow. Been having sub zero temps regularly also. Merry Christmas everyone!  Glen
borat


Joined: Nov 10, 2007
Points: 2692

Re: Ariens 824 engine question
Reply #7   Dec 23, 2008 5:57 pm
Try putting on a "longer" turtle sticker on the  engine. 

We're getting a good dump up here on the north west shore of Lake Superior.  Looks like at least five inches out on the driveway now and it's not done.  Does anyone here look at the radar maps on their local weather  web sites?  I look at mine regularly (it's in my favourites).   It's pretty accurate.    It's animated so you can see the storm moving on the screen.  You can see how much of the system has passed and how much more to come.  Neat stuff.   

borat


Joined: Nov 10, 2007
Points: 2692

Re: Ariens 824 engine question
Reply #8   Dec 23, 2008 5:57 pm
Try putting on a "longer" turtle sticker on the  engine.  

We're getting a good dump up here on the north west shore of Lake Superior.  Looks like at least five inches out on the driveway now and it's not done.  Does anyone here look at the radar maps on their local weather  web sites?  I look at mine regularly (it's in my favourites).   It's pretty accurate.    It's animated so you can see the storm moving on the screen.  You can see how much of the system has passed and how much more to come.  Neat stuff.   

borat


Joined: Nov 10, 2007
Points: 2692

Re: Ariens 824 engine question
Reply #9   Dec 23, 2008 5:57 pm
Try putting on a "longer" turtle sticker on the  engine, or just stretch the existing turtle's neck out a bit.   

We're getting a good dump up here on the north west shore of Lake Superior.  Looks like at least five inches out on the driveway now and it's not done.  Does anyone here look at the radar maps on their local weather  web sites?  I look at mine regularly (it's in my favourites).   It's pretty accurate.    It's animated so you can see the storm moving on the screen.  You can see how much of the system has passed and how much more to come.  Neat stuff.   

This message was modified Dec 23, 2008 by borat
Replies: 2 - 9 of 9Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.