Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

One of my neighbours just gave me his lightly used Sears 10/28 snowblower. He is physically unable to use it any more and was having problems with it for the last couple of years. I suspect the main problem was lack of use and old gas. The machine looks practically new and is very clean. Its in better overall shape than my machine. The only two things I've found missing are the knob on the gear shift and the bolt that holds the top of the tube that the oil dip stick goes into. The engine would not start when I got it.

I took the cowling off and low and behold, the end of the tube from the primer bulb was frayed at the carburetor end. I cut off about 1/4" and put it back on. I've bought a new tube and will replace the old one as soon as it stops snowing and the sun comes out.

The engine starts up but now surges. I've put some Sea Foam into the gas and let it run for about 10 minutes. The engine is running better and does perform better under load. It still needs work.

According to what I've read from searches on this forum and on the Tecumseh Technician's Handbook for 3 to 11HP L-Head Engines the next thing is to take apart the carburetor and clean it. I've never done a carburetor disassembly, cleaning, rebuild before so any advice on cleaning agents, things to watch out for, errors in the handbook or any other advice people would care to offer would be appreciated. I will be getting a carburetor kit from the local L&G since I'm positive gaskets and O-rings need to be replaced.

I don't have the engine serial number but will post it once the snow stops ( Thursday morning is the current prediction).

If I still have a problem then it will be time to look at the governor.

1. The carburetor controls runs a lot more freely and the thing looks cleaner;
2. The fuel and primer lines have been replaced;
3. I did not replace the welsh plugs, everything else from the kit has been used except the large O-ring, see below;
   
4. The engine either runs at a very fast idle or dies;
5. I can keep it running by keeping the throttle open, the idle adjustment screw doesn't seem to help;
6. The large O-Ring that goes on the top rim of the float bowl was too big, I've used the old one as an interim solution;
   
7. The O-ring on the idle adjustment is flopping around on the screw shaft;
8. I may have the rods from the governor in the wrong holes of the two plates they connect to;
9. When I try to blow snow the engine does not react to increased load and the snow dribbles out the chute;
10. There is a loose spring n the manual throttle assembly;
11. I have not cut the slot and removed the screw.

Aside from tha,t things are working perfectly. I'm also learning a lot of respect for anyone who can fix and adjust a carburetor. I will keep plugging away

I looked at the Tecumseh manual again and found the following things have happened:

1. As I suspected the manual throttle plate that one of the rods to the governor connects to is supposed to be up and not down.
2. I've used a dremel tool to cut a slot in the remainder of the broken machine screw. Is still stuck and the slot is starting to deform. I'm not sure if heating the unit will help but the only other solution is to drill it out and tap the hole;
3. I have now got the correct sized O-ring installed on the fuel cup;
4. When the throttle was set to "Fast" the engine would rev way to high. In fact oil was starting to come out of the breather tube. I repositioned the governor lever and it now runs better. I have to get a tachometer to set the correct high speed RPM but we are now in the ball park.
5. Gas still leaks out if I'm not running the engine. I think the inlet seat needs to be reinstalled, I suspect its askew;
6. I haven't figured out what is wrong with the idle adjust screw. there is a small brass washer on it outside of the O-ring. The washer isn't fixed to anything, isn't pressing against the o-ring and moves back and forth along the shaft. I did find one diagram for a different type of carburetor that showed a spring between the head of the screw and the brass washer. The spring pressed the washer against the o-ring. I also noticed that when I prime thee appears to be a misty jet coming out of that area. I will reread the installation instructions.
   

 Not to be a smart ass but you had me laughing for a while there. 

 I admire your perseverance and patience. 

However,personally, I'd have tossed that carb into orbit and bought a new one by now.

Good luck to you and thanks for the updates. 

No probs.

As to why I haven't gotten a new one:

1. This is the first time I have done a carburetor cleaning, its a learning experience and therefore perseverance is the name of the game, I have to learn from my mistakes;
2. I an cheap.
3. This is for the "spare" snowblower, I can afford to have it out of service while I "play".

As far as I can see most have my problems are from inexperience and a fair bit of dumb luck.

I am learning and thats the main reason for posting, so people can learn from my mistakes, giving then a good laugh is an added bonus.

borat wrote:

Thanks Denis.

The Yamaha RD's are hot rod street bikes from the early 1970s.  The twins run pretty smooth compared to the small single Kawasaki you were riding.  The Mikuni VM28s hold their adjustment very well.  The idle screw and air screws both are spring loaded and don't move much.  They are the only two adjustment screws on the carbs.  I'm presently working on converting the points ignition system to an all electronic system.   I will also be installing a special CDI that I can plug a hand held controller into for adjusting the engine timing while the engine is running.  The programmer can hold up to ten programmed timing curves depending on what type of riding you want to do.  If you want to run with high fuel efficiency and cooler engine, there's a timing curve for that.  If you want all out horse power (for short durations) there's a curve for that.  Two stroke engines are sensitive to timing changes.  The timing requirements are considerably different at 3000 rpm vs. 10000 rpm.  Points ignition cannot deliver the timing performance that a electronic dynamic system can. 

I'm still a few weeks away from having the RD400 ready.  Will post some pics when it's ready.