Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Ariens624E Likes to run with choke part way on
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions |
|
NHsnowman
Joined: Dec 17, 2007
Points: 12
![]()
|
 |
Ariens624E Likes to run with choke part way on
Original Message Feb 19, 2008 3:43 pm |
|
HI all, I just bought an Ariens 624E snowblower and it was deliverd today. My question is it seems to run best with the choke partially on. I havn't been really able to blow any snow to really warm it up good as all out snow here in NH is basically solid as ice right now. Could it be that it just needs a good long time to warm up? Also it is an OHV engine and I have heard that they sometimes need to be run with choke partially on because the emmision seetings cause them to run so very lean. I followed the manual exactly and started it on low throttle full choke and then slowly backed off the choke but when i get to the last choke seeting it starts to sputter out. If i return quickly to the higher choke setting it goes right back to running great again. I was hoping someone had some info or thoughts on this. Any insight would be greatly appreciated. |
NHsnowman
Joined: Dec 17, 2007
Points: 12
![]()
|
 |
Re: Ariens624E Likes to run with choke part way on
Reply #3 Feb 19, 2008 5:44 pm |
|
The engine is a 6hp OHV Techumsa and it is brand new.
This message was modified Feb 19, 2008 by NHsnowman
|
NHsnowman
Joined: Dec 17, 2007
Points: 12
![]()
|
|
|
Re: Ariens624E Likes to run with choke part way on
Reply #4 Feb 19, 2008 7:39 pm |
|
Also one last question. Does it do any harm to the machine to run it with the choke slightly on? Thanks for all the info. |
Paul7
 
Joined: Mar 12, 2007
Points: 452
![]()
|
|
|
Re: Ariens624E Likes to run with choke part way on
Reply #6 Feb 23, 2008 12:10 pm |
|
I had a 5hp Ariens (Tecumseh) that after a few years liked to run better with the choke partially on. I ignored it and just ran it that way. After a short while the machine became so hard to start that I needed to use ether everytime I fired it up. Finally broke down and serviced the carburetor and made sure that the setting were right. I never needed ether again...3 pushed of the primer and it fired right up, and it ran great without the choke partially on...actually it ran much stronger. Look, you have a brand new machine...it should run like a brand new machine. Have the dealer fix it or if you bought it from HD take it back and exchange it for one that runs right.
|
daswede
Location: Merrimac Valley-Mass.
Joined: Feb 23, 2008
Points: 37
![]()
|
|
|
Re: Ariens624E Likes to run with choke part way on
Reply #7 Feb 23, 2008 1:22 pm |
|
Hi everyone. New member here ref: Ariens 624E Sorry to hear of your problem I have a new Ariens 724E this year, and mine runs just great. Bought from a dealer. It starts quickly with just the recoil starter,1/2 choke,idles down nicely with no choke. I guess i echo others here that you have to take it back ,if you bought from a dealer, and have it checked out. |
NHsnowman
Joined: Dec 17, 2007
Points: 12
![]()
|
|
|
Re: Ariens624E Likes to run with choke part way on
Reply #9 Feb 26, 2008 2:09 pm |
|
HI all, Just thought I would throw out an update on my new machine. Went back and re read my manual and figured out what I was doing wrong and it has run like a champ ever since. I have to say it just feels better made than the sears machine it is replacing. Even got to test it out on a nice powdery 6" snowfall and it threw it 50'+. Tonight/tommorow will be it's true test though 6-10" of heavy wet snow, (going to put us over 100" for the year). As I said just wanted to update so as the machine didn't get a bad rap for my stupid error. |
Snowbound
Joined: Feb 17, 2006
Points: 76
![]()
|
 |
Re: Ariens624E Likes to run with choke part way on
Reply #11 Feb 26, 2008 4:31 pm |
|
HI all, Just thought I would throw out an update on my new machine. Went back and re read my manual and figured out what I was doing wrong and it has run like a champ ever since. I have to say it just feels better made than the sears machine it is replacing. Even got to test it out on a nice powdery 6" snowfall and it threw it 50'+. Tonight/tommorow will be it's true test though 6-10" of heavy wet snow, (going to put us over 100" for the year). As I said just wanted to update so as the machine didn't get a bad rap for my stupid error. What were you doing wrong?
|
|
|
