Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

   I just picked up a new Husqvarna 10527SBE, wanted to get the Ariens 926LE but everyone ran out of them. Looked at the Toro but was over my budget for the features I wanted. I liked my older Areins but it just didnt have the power for the heavier storms and the EOD. Also my drive is single wide 85'+ long, and due to an adjasent drive I have to double blow the snow for about 35 ft. I liked the power steer, and remote hood deflection feature on yhe Husky. Does anyone have this machine and if so has it lived up to your expectations? Im hoping for some snow in the next couple of days to try it out.

Hi Jubol I have a poulanPro 11530SE  that looks just like the Husqvarna 1130SBE I could sure use a service manual for it.

Thanks

Ron

Hey everyone! New to the forum.

Just picked up a Husqvarna 10527SBE. Have only used it once but it worked quite well in semi-heavy (26-30 degree temps). The snow was probably around 12" deep and throwing it 20-25'. It handled the 18 inches (or so) of plowed snow at the street without problems also.

It was a somewhat spur of the moment purchase but the price was just too good to pass up. The local Ace Hardware had them marked down for the season. Their regular price was (I believe $1149.99) and it was on sale for $929.99. I actually went to Ace to get a snow shovel.....they were sold out so I got the Husky. It's alot more fun to use than a shovel too. Had I been shopping for a snow blower, I would have looked to Ariens. From what I've seen, my Husqvarna was made by the same company that makes (at least some of) the Ariens models. (AYP?) I doubt that I could have purchased the same Ariens for even close to the price I got this one for.

Snow is falling now with 4-8 inches expected by the time is stops tomorrow evening. I hope I don't have any problems but I'll put it to work again tomorrow and report its performance.

I'd also be interested in a repair manual also, if possible.

Thanks!!

P. Hicks

Blower worked well! We only had 4 or 5 inches total but there was a little drifting. The deepest drifts were only 8 or 10 inches, though. The temps were in the high 20's to low 30's so the snow was fairly heavy. The snow that was closest to the ground was really wet and heavy....almost slush. Went through all of it with no problems at all, as expected.

My only complaint about this machine is it's size for my use. My driveway is about 110' long and single wide for about half of its length. A smaller snowblower would have been better for maneuverability. I have to overblow about half of my drive and wanted a machine big enough to do that without any problems.  I guess a "too big" snow blower *can* be a problem but I'd rather have that as a problem rather than a machine that won't handle the snow.

tgregoire wrote:

Hi tgregoire,

Had the same problem last year on my 10-30. return it to dealer for carb ajust. and he reroute the cable ...much easier play on the lever. Also wath that there is no water in a cable that goes down and up. When it is very cold the water freese and the cable jam. Good luck .

Paid  $2000 canadian for that thing and i am deceive ,bucket is not aligning with the rest and it pull on the left.dealer says there is nothing he can do I am gone to sell it and by a blower that fit on my Polaris

Ciao

Also make small cut on the cable black sheat as it goes down so water will drip from these opennings.That cable is way too long but what can you do.it is made that way.

Good luck

Claude from freezing Quebec

jubol wrote:

I recently purchased the 1130SB-LSb.  We have not had any recent storms to use it yet.  Fred, can you pass along the repair manual.  Thanks.

Svenster- It is with great sadness that I must tell you that Jubol(Fred) passed away on 5/1/08. He was laid to rest at Arlington National Cemetery.RIP

Marc

Thanks Marc for the info.  My thoughts and prayers go out to Fred, his family, and friends.

                  I am in Canada.    We have a different line of Craftsman snowblowers than are sold in the USA.     Our higher price models are built by Husqvarna, and offer all of the same featuresas the husq models but are red instead of orange.

I have the Husq built Craftman 52993 , 27 inch, 305  14.5 torque Briggs and Stratton, Hydrostatic drive (built by Hydro Gear)  It has trigger type power steering,  heated grips.  , the discharge shute is operated by a short travel lever and the chute deflector is operated by another short travel lever on the console panel. The hydrostatic is operated by a single lever, with no clutching.  It is variable speed,  move the lever forward   to go forward , move it back to  backup, the further you move the hydro lever forward, the faster is your ground speed. Same with reverse. You can shift directly from forward to reverse  without stopping .Torque is the same at all speeds.  The torque multiplication is over 20-1 . You can travel much slower (creeper speed) than any friction drive snowblower.  so you do not stop moving forward , no matter how deep the snow is.

I have had  this  machine for only a month , but we have had 4 big storms, over 50 cm (20 inches)  for one storm and over 30 cm (12 inches) for the others.  My  machine has worked very well,  My neighbours all have similar size snowblowers , John Deere, Toro, MTD, and an older Murray built Craftsman, They are 26-28 inch,     11.5 -14.5 torque and 11.0 to 11.5 horsepower.  Where the snow plow pushes the snow into the end of the driveway is always the hardest . It can be up to 4 feet deep,  My hydro equipped machine will go through it without stopping at a creep speed. , the engine speed doesn't change and its sound does not change. The other snow blowers will not go directly through this heavy packed snow. The operators have to back up , make several tries at it, pushing their machine and  wiggling them to get through , their engines lugging down and making a lot of noise. 

  I am answering an old post,  but it is still snowing.

YIKES - This thread is so old, Husqvarna does not even make the 10527SBE any longer and one of the original posters died almost 3 years ago!!!