Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > 2000 6.5 HP Tecumseh lawn mower will not start
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions |
|
dzton
Joined: Jun 23, 2005
Points: 8
![]()
|
 |
2000 6.5 HP Tecumseh lawn mower will not start
Original Message Jun 23, 2005 11:57 am |
|
I purchased a Scotts self propelled mower from an individual who had it sitting outside. It did not start. I replaced the spark plug, fuel line, sanded the magneto, emptied the old fuel and replaced with new fuel. I cleaned out the carb as well as replaced the gasket the needle and the seating. The engine will start but then stops. I am puzzled at this point. Does anyone have any suggestions??? dzton |
dzton
Joined: Jun 23, 2005
Points: 8
![]()
|
 |
Re: 2000 6.5 HP Tecumseh lawn mower will not start
Reply #6 Jun 23, 2005 12:59 pm |
|
engine = ovrm120 - 22033d engine family = ytpxs - 1951aa displacement = 195 - 0221j |
dzton
Joined: Jun 23, 2005
Points: 8
![]()
|
|
|
Re: 2000 6.5 HP Tecumseh lawn mower will not start
Reply #9 Jun 24, 2005 2:59 pm |
|
Would the breather element effect the starting and stopping issue?
|
dzton
Joined: Jun 23, 2005
Points: 8
![]()
|
|
|
Re: 2000 6.5 HP Tecumseh lawn mower will not start
Reply #12 Jun 24, 2005 5:43 pm |
|
Breather element or air filter? Breather element. I already replaced the air filter.
How nasty was the carb before you cleaned it? Nasty!
Did you clean the bowl nut? All 3 holes? Yes.
If you look into thoat of the carb...and prime...do you see fuel coming from the tip of the main nozzle? No, I removed the carb, broke down the carb removing the main nozzle. I did need to add two new "O" rings. (Use a flashlite too look in.)
Did you hook the wire clip of the needle over the float the float tang? Yes. Did you set the float level? No. Not sure how I would set the float level. It appears the needle goes into its inlet once placed on the float.
If you loosen the bowl nut...does fuel flow out? Yes
When you installed the needle and seat...did you have the carb off of the engine? Yes.
|
buttlint
 
Joined: Oct 14, 2002
Points: 791
![]()
|
|
|
Re: 2000 6.5 HP Tecumseh lawn mower will not start
Reply #13 Jun 24, 2005 6:44 pm |
|
Dont worry about the breather....they "never" good bad. When you replaced the 2 o-rings on the main nozzle, are you sure you removed the old one. (The top one usually stays put and has too be dug out.) Are the governor-carb linkages as they were before you removed the carb? Again...make sure it is priming when you press the primer bulb. (You should see it coming out of the end of the main nozzle, into the throat of the carb.)  Be sure that # 241 is in place....screw #238 must be in its holes, or the carb will never prime. (The screw blocks off a common passage that it shares with the primer system.) Without the screw in place....the primer charge just blows out of the hole and doesnt reach the float bowl. |
dzton
Joined: Jun 23, 2005
Points: 8
![]()
|
|
|
Re: 2000 6.5 HP Tecumseh lawn mower will not start
Reply #14 Jun 24, 2005 7:03 pm |
|
Dont worry about the breather....they "never" good bad.
When you replaced the 2 o-rings on the main nozzle, are you sure you removed the old one. (The top one usually stays put and has too be dug out.) When I remove the nozzle there was no o-rings there.
Are the governor-carb linkages as they were before you removed the carb?
I pretty sure, not 100% positive.
Again...make sure it is priming when you press the primer bulb. (You should see it coming out of the end of the main nozzle, into the throat of the carb.)
Do I perfom this with the carb off the engine? Be sure that # 241 is in place....screw #238 must be in its holes, or the carb will never prime. (The screw blocks off a common passage that it shares with the primer system.) Without the screw in place....the primer charge just blows out of the hole and doesnt reach the float bowl. The two screws are in the holes.
|
|
|
