Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I have an old Ariens snowblower that is in good shape but with a tired engine. I've been looking into a new replacement. The logical candidates seem to be the Tecumseh OHSK70, the B&S Intek 7.5, and the Honda GX200. 

The Honda seems to have the most torque (10 ft lbs) but is also by far the most expensive - $500 versus around $300 for the other two.

I have never seen a torque figure quoted for the Tecumseh, but it seems like the Intek 7.5 is around 7 ft  lbs?

Another engine that I came across was the Robin Subaru EX series, a 7hp OHC engine that has a lot of advanced features but isn't much more than the B&S or Tecumseh. They all have the same crankshaft (3/4") and height (about 4.17").
B&S sent me data sheets on the replacement: the Honda dealer has an employee who did one; and Tecumseh gave me all the dimensions and concerns (mostly about fitting the chute crank under the engine) but they all seem like they'll work.

I live in Boston MA and the current unit is a Tecumseh H50 on a 1970 Ariens. I checked the compression and it's 65 psi on the first pull and 75 psi after 2 or 3 (by hand pull). I do the sidewalks up and down the street for  some older (or lazier) neighbors so the kids can walk to school without walking in the road. The blower is great because it compacts the snow a bit and the biggest problem here after a snowstorm is finding a place to put it. I've used the unit 8 times so far this season.

Here's the new and the old.

Imagine my surprise after  hearing from various sources that this change was difficult or impossible (local dealer) to see that the new engine mounts perfectly on the old studs for the H50. They're too short and will have to be drilled out and  longer bolts used, but everything will bolt right on.

A  couple of ujoints for the chute crank and we'll be done!

i have swapped a lot of the 10 and 11 inteks for old tecumseh.

havent had many problems with the swap.in fact we usually do it for the old engine.

we sell the iginition and carbs and make a few bucks here and there.

the ariens is sometimes a bit more time ,like you said you will have to modify the chute crank.but its not to bad .and wow what a machine you have when your done.

later chris 

Reminds me of an Escalade sitting next to an old Dart. 

Congrats, that's going to be a great set up when you're finished.

Only one little four barrel.



Now that's a snowblower engine.



Garandman, People love those Inteks. You should be real happy. Don't forget the pics of the conversion if you can. It should be great.

Garandman wrote:

It doesn't seem like you left a message, ut here's the completed machine.

Just saw this part of your message.

[quote]I just bought a used Ariens just like the picture that you posted.  The model # and serial # were cut off of it so I am not able to figure out the best matching model number for this blower.  You said you have one along the same line, mine matches the picture exactly, does yours?  If it does, would you give me the specs of it along with Model # so I can look up more information about it?  It's a very clean machine with a tired motor and some light carb work that needs to be done.  I am also debating about changing motors or repairing the one I have.  I have found some really good engine prices online and compared to fixing the existing engine, it is much more worthwhile just to buy a new one.[/quote]

Have to add another post because the Moderators (who must be strange people indeed) removed the ability to edit posts......

The engine is a 7.5hp Intek Snow with a 3/4" shaft and electric start. The shaft was a little longer than requird on the one I bought as a "scratch and dent" special - I cut it off with a hacksaw. I had to drill out the old studs and replace them with longer bolts. I have a personal website with more pictures and details, PM me if you need more info.

Here's a comparison between the new OHV Intek and old H50.



Because I bought an 8hp Ariens I haven't actually used this one yet. I'm bringing it to my brother in  a week or so. He has a teenager to wring it out.

Garandman wrote:

Wow, you did a nice job at cleaning that machine up.  Looks brand spanky new!  I believe mine is pretty much the same exact model, could you tell me the Ariens model number of yours?  So you went 7.5HP Intek, I am still debating on which engine to put into my frame.  I was hoping to go to at least an 8.5 or 9.5HP motor but need to be careful that the internal components can handle it. 

Mind if I ask the website where you got your engine from?  I remember seeing those "scratch and dent" ones, but didn't save the link.

Thanks!

pcardone wrote:


The blower unit is 10995.

The 8.5+ hp engines have the shaft in a different location and as this unit only has one blet, you're pushing it.

I bought it at Small Engine Warehouse.

Garandman wrote:

Thank you!!  You answered questions that I wasn't able to find yet.  So basically I should prob go the same route you did, Intek 7.5 and make the linkage arm for the chute.  I could prob go to 8HP without a problem but no higher. 

Awesome!  Thank you for all the help!!!