Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Drive system on 1970 Ariens?
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions |
|
Garandman
Location: South Boston, MA
Joined: Mar 10, 2005
Points: 341
![]()
|
 |
Drive system on 1970 Ariens?
Original Message Mar 18, 2005 3:08 pm |
|
I called Ariens about my 1970 manufacture Sno Throw. The front part is 10995 and the back, "tractor" section is either #10942 or #10954. I'm going to order the service manual for it, but was curious about the drive system. It has 4 speeds forward and one reverse. The forward speeds seem quite "direct" while reverse has some slippage built in and you can stop it readily. I've read about the friction disk system, but this doesn't seem to have one? Not sure what I'm looking at in the exploded view (I'm spoiled with 3D solid modeling). Also, are replacement decals available for this vintage of machine? Finally, I have new skids (two sided) and they seem to be a slightly different orange, possibly because of the effects of 35 years aging. Does the dealer sell spray paint, or can I match it from another brand of spray can? TIA
This message was modified Mar 18, 2005 by Garandman
|
Garandman
Location: South Boston, MA
Joined: Mar 10, 2005
Points: 341
![]()
|
 |
Re: Drive system on 1970 Ariens?
Reply #19 Apr 24, 2005 4:02 pm |
|
OK, assuming the image posts.... I have the snowblower nearly completely apart. Not only that, some of the parts are in different states..... I got a new friction disk but haven't received the manual I ordered yet. So I've been checking various bits and pieces and startd to dissasemble it preparatory to replacing the friction disk. But I'll be darned if I can figure out what the "connecting brackets" are?
This message was modified Apr 24, 2005 by Garandman
|
Dave___in___CT
 
Deliberate often...
...decide once...
Location: West-Central Connecticut
Joined: Sep 17, 2002
Points: 3159
![]()
|
|
|
Re: Drive system on 1970 Ariens?
Reply #21 Apr 24, 2005 5:50 pm |
|
On a related note, I'm starting to debate the wisdom of upgrading this old unit versus buying a newer one. Putting on a new engine, friction disk, and some other minor repairs etc will cost me about $300 net (I can sell the old engine since it's still running). Or, I can sell this unit for about $200 and buy a newer used model. There are two ST824's in excellent condition in the paper for $700 and $750. So it's $500 and no work versus $300 and some work, after which I'd still have a 35 year old snowblower with a new engine.
My dad bought this one new in 1970 so there's some nostalgic attachment. Another option is to repair the necessities and just keep using it. But the newer models allow the auger to be stopped, while this model keeps them engaged all the time. So the new design seems safer. I'd consider keeping it as is but don't have the room.
I took the engine and auger off this weekend as well as the bottom plate for a thorough inspection and cleaning. I have to admit it's built like a tank. The gear housing in the auger is massive.
No urgency now as the "last" snowstorm turned to rain. It's possible we'll get more, as the famous "April Fool's Day" storm of a few years back demonstrated.
I hear ya' !!!
I buy used and new equipment for my own use... and it's usually the same with me... Fix ? Use as-is? New ? The brain spins ! Usually it woks out excellent... Good luck... Dave...
Whether you think you can or you can't... you're right.Henry Ford  BCS Tractor & snowblower
|
RalphS
There's a reason for more than one snowblower.
Because.
1974 Ariens 824 SnoThro
197? Ariens ST270 SnoThro
1988 Ariens ST824 SnoThro
196? REO Snowblower
1960 Ariens SnoThro
1964 Ariens SnoThro
Location: MA
Joined: Dec 21, 2004
Points: 70
![]()
|
|
|
Re: Drive system on 1970 Ariens?
Reply #23 Apr 25, 2005 10:12 am |
|
Fred- That paint doesn't look that bad. Wait until I post before and after pix of my '88. The "connecting brackets" are just short (maybe 4" -6" long, I can't remember) rods with a 90 degree bend in them- they are cotter-pinned into brackets inside the housing. There is one on each side. When you remove these "brackets", the drive assembly should kind of just rotate down and towards the back of the machine. I couldn't see them in the pix you posted. I don't think the early 70's drives were all that different, but you may not have them. When I originally was working on my '74, I couldn't see how to get at those 4 little nuts holding the bearings in- once I disconnected these brackets, access was great. Let me know if you need any help- like I mentioned before, the manual can be a little confusing. I can take some pix, but I have never gotten around to figuring out how to post them. I can PM them to you if you want. Good Luck. Ralph |
|
|
