Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides

Member Profile


pjm14945

Name Pete Mulligan
Email Address private
AIM
YIM
ICQ
Gender
Age
Location
Personal Quote
Privileges Normal user
Rank
Points 2
Number of Posts 2
Number of Reviews 0
Date Joined Jan 25, 2011
Date Last Access Jan 27, 2011 11:14 am
pjm14945's last  
Re: Tecumseh 6.5 hp timing or valve issue?
#1   Jan 25, 2011 10:28 pm
Thanks for your reply Trouts.  It will generally start 3 or 4 times but never run for more than 30 seconds.  After that, it will not start so I assume that eventually I would flood it by hitting the prime too many times.  After it runs for 15 seconds and then stalls, it will not start up again unless I prime for 3-5 times.  Once it is running, I have tried to spray starter fluid into the throat but that does not help and seems to have the same affect as giving it some throttle.  It seems to stall the engine out.  I have not tried to hit the prime when it is running. 

I was concerned that when I cover the throat with my hand, there does not appear to be much suction from the throat (i.e. air flow from air filter removed).  If there is not a good air flow, would that explain why the engine is not running?

How do I check the valve lash?  Also, how do I perform the leakdown test?  It sounds like I'd need to know when the piston is in the compression stroke and then forcing air into the spark plug hole.  Would that have to be pressurized air to hear for a leak threw exhaust or carb?

-Pete

Tecumseh 6.5 hp timing or valve issue?
#2   Jan 25, 2011 12:41 pm
I bought a used Murray gokart that has a great frame and a OHH65 model Tecumseh 6.5 hp engine.  The engine is hard to start.  The engine has a prime bulb and we can get it started with 5 primes but it will bog down and die when we throttle up.  It is also not idling well and will die after only 30 seconds.  We pulled the carb and thoroughly cleaned it using a rebuild kit.  The carb had white cake and crud under the welsh plugs.  We used wire to clean the 3 small jet holes.  I also pulled the gas tank and cleaned it out with fresh gas. I replaced the fuel line as it looked worn.  However, even with fresh gas and a good cleaned carb, the engine still will not throttle up.  We can get it started but it will die soon and will stall when we throttle up.  When we do get the engine to start, I've spray starter fluid into the air intake (w/o filter) but the engine does not power up.  In fact it seems to die when we inject starter spray into carb.

I checked for compression and found 60 PSI after 3 pulls.  Not sure what compression should be but that seemed OK.

I pulled the air filter and I can see the primer bulb is squirting gas into the carb.  I put my hand on the air intake and while someone else is pulling starter, I don't feel a vacuom on my hand.  When the engine does run, I see some gas spit out of the air intake.  I was thinking the exhaust might be clogged, so I pulled the muffler.  Without the muffler, the engine still does not start nor run well.  Even w/o the muffler, I don't feel any suction on my hand over the air intake while someone pulls starter cord. 

I see good spark on the plug and have replaced the spark plug using .030 inch gap. 

I'm thinking it could be a valve or timing issue.  Does anyone know how to check the timing on a Tecumseh engine?  Any ideas as to what to check next?

Thanks.

-Pete

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42