Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Well I couldn't let it go.
It was just bugging me why the thing was so pitiful when it came to it's throwing distance.
So a few days ago I removed the steel that formed the center hub around the auger shaft.
Then made plates to support the center of the paddles and welded them in place.
Now it looks like most of the other Toro SS blowers out there.

Tried it out, and it really didn't make much if any difference in the distance.
And it had no effect on the engine performance.
So back into the garage we went.
Decided there was only one more thing to modify.
So I removed the stock pulley and replaced it with a stock pulley from another Toro SS.
Most of the pulley's are the same. But I think it may have come off a CCR 2000.
The stock SC pulley is 7 1/2" in diameter.
The replacement one is just a little less than 6" call it 5 7/8"
So a full 1 1/2" smaller.

Now the blower is set up just like most other Toros out there and the impeller
will be running at the same RPM as those blowers.

The really good news was that after I measured what new belt length I was going to need.
I found a great and helpful belt supplier on line.
vbeltsupply.com
I gave them the measurements told them what I needed and they said no problem.
$21.00 ($10 for the belt $11 shipping) and four hours later it was on it's way.
I should get it Monday afternoon.  So by Monday night I should know something.
It will be interesting to see how the added auger RPM directly effects the throwing distance.
And how the engine responds.  Removing the center hub steel plates probably dropped off
about 6 or seven pounds.  We'll see!

 

The center area of the paddle is wider than the chute opening.

But the upper interior portion of the blower housing itself, just below the
chute opening is funnel shaped.
That shape is what allows the snow to flow up and out of the chute.

Well received the new belt this afternoon.
Put it on, and gave the blower a try.
It's better, but not enough to say "oh boy look at that".
Not enough to get out my video camera.

After trying out the SC I sat it side by side with my 210R.
So.... here are my thoughts up to this point.
The interior of the blower housings are the same design and shape.
The chute angles are the same. The chute holes are the same diameter.
The width of the blower mouth on the 210 is 21"
The width of the blower mouth on the SC is right at 23 1/4"
So the SC cuts a path that is only about, let say 2 1/4" wider than the 210.
 But lets say 2 1/2 or 3" wider.
The 210 has the 141cc R-tek which is let say putting out 5.5 hp.
The SC has the 141cc R-Tek with the ported piston and cyl walls.
Supposedly putting out 7hp.
I changed the center paddle supports so it is like most any other Toro SS including my 210.
The pulley is now the same size as most other Toro SS.

Granted the SC cuts a little wider path buts it's got 1 1/2 to 2 more HP than my 210.
With that added power it should have no problem with taking in a little more snow.
But the question is, why does it throw so poorly compared to my 210.  And most other
Toro SS in the 5hp range? The CCR 2000 with a 4.5hp throws better.
Same auger design same pulley size.

There is only one thing left that I can think of.
Maybe it's that third paddle.  Maybe that third paddle is bringing in snow to often.
Maybe it's in some way disrupting the flow of snow in the housing, who knows.
I honestly don't know what else it could be. The third auger is the only design element that is different between the SC and the 210.
It's the only thing that is different than any other Toro.  And most any other SS I've ever seen.
I would love to know what the engineers thoughts were behind thinking there was a need for a third paddle.
Maybe I'm missing something, but it just make no sense to me.
That a 7hp taking a 2 1/2" wider cut.  Can't throw snow at least as well as a 5hp
cutting a slightly smaller cut.
Especially when blowing only 2 or 3 inches of snow.
What do you think, pull the third paddle?

They may have been going for more volume than distance on this model.
Hence the three paddles.  But from my experience they may, for what ever design and or manufacturing reasons.
Missed the mark just a little.  This blower really has some rather different performance characteristics than most 2 cycle SS.
It is a very gusty machine.  You can push it into just about any type or depth of snow.
And it will bog down.  But it digs it's heels in at a certain RPM and almost refuses to go any lower.
It's seems to have a lot of torque.  Which could come from the three auger design.
As Borat has said it takes smaller bites.  Unfortunatley in those situations it's only throwing the snow
maybe 5 to 7'. Which can sometimes be enough distance.  But more often than not it's a little short.
And you may have to end up re-blowing.  Today I didn't really have good snow to test it in.
But at certain times it would throw maybe 15', which would be fine.
If it would throw that distance consistently.
Were supposed to get maybe 6" or more of new snow tomorrow afternoon and evening.
Don't know what the torque curves for the two engines look like.
Haven't measured the diameter of the SC and the 210 paddles so don't know if the tip speeds are the same.
But the auger RPM should now be the same.
The reason that I said that they may have "missed the mark a little"
Is because you can always slow down your forward speed to lessen the volume of snow your putting into the blower.
But if the throwing distance is poor because of the third paddle.  That problem isn't something a person can work around.
By adjusting there forward speed.  Blowing a large volume of snow a short distance isn't real helpful if you have to re-blow it.
It works really well for doing sidewalks.  As it will really move along as fast as you want to go.  Being able to adjust how fast you
want to move forward by tilting the unit further forward is something I really like.

Your right, If I were to pull a paddle I would have to make sure that I get the two paddles
located correctly on the shaft.
If not, the thing would probably vibrate itself down the street.