Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > How do you clean your carburator?

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
bcjm


Location: Washing DC Area
Joined: Dec 2, 2011
Points: 25

How do you clean your carburator?
Original Message   Dec 6, 2011 4:29 pm
One of my local shop told me they soak the carburator in a acid fluid over night to clean everything before rebuilding.  Wondering if that is what the professionals' common practice.   If that is the case what kind of acid do they use?  I do have a bucket of acid that I use to clean car parts.  I am worry it is too strong to clean the carburator.
Replies: 5 - 14 of 19Next page of topicsPreviousNextNext page of topicsAllView as Outline
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: How do you clean your carburator?
Reply #5   Dec 7, 2011 11:52 am

>>One of my local shop told me they soak the carburator in a acid fluid over night

 

   They did not literally mean “acid” or probably it was your choice and intended to generically  mean some stuff that ate away gum and dirt in a carb.

 

>>>Wondering if that is what the professionals' common practice.

   Most shops use a one gallon of can solvent dip or ultrasonic bath with a light soap/detergent.  You can get a can of solvent that comes with a small dipping basket at most auto parts places for $20 to $40.  A good ultrasonic tank for small carbs is $2000-$2500.

 

    What the other posters have said is all good advice and they may never have run into a problem.  Gas does not do much for gum and the same for carb spray.  For very nasty carbs those are not enough and the dip able to soften and loosen gum poking can’t reach.  If you’re doing 20-50 carbs a season dipping helps you avoid the occasional removing of a carb that’s not quite clean.

RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Re: How do you clean your carburator?
Reply #6   Dec 7, 2011 1:24 pm
I've seen people mention that Harbor Freight sells some small ultrasonic cleaners. I think they may also be able to heat the liquid during cleaning. I seem to recall reading that they can be had for around $40 sometimes with a coupon. Some people apparently use them to help clean their carbs, etc, even in a homeowner-type setting. So there is at least some sort of inexpensive ultrasonic solution, for occasional use.
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: How do you clean your carburator?
Reply #7   Dec 7, 2011 2:29 pm
    As an alternative to going to dip I picked up an HF ultrasonic with heater, their good one, and used it on many carbs.  I can't say it made any difference over many carbs.  I'd still end up with an occasional carb I'd have to do again.  I eventually went to dip and rarely have a problem.  I do quite a few carbs and many that are very old with weird buildup of white, grey, light green, dark green, tan, brown and deep brown.  The only time I use ultra now is on very nasty carbs after the dip in hopes it might shake out some crud the dip loosened in interior passages. 

   One local dealer went to ultra two years ago and says that's all he uses now.  His tank cost $2500. 

This message was modified Dec 7, 2011 by trouts2
CharlesW


Joined: Jan 9, 2011
Points: 76

Re: How do you clean your carburator?
Reply #8   Dec 7, 2011 11:05 pm
It seems like I have read that many carb cleaners will damage the gaskets and rubber O-rings. Seems likely that the cleaner might also damage any rubber seats or needle tips that it comes in contact with.

As with many things, knowing what you are doing is probably a good idea.

Comments from the experts????

trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: How do you clean your carburator?
Reply #9   Dec 8, 2011 10:11 am
   

>>It seems like I have read that many carb cleaners will damage the gaskets and rubber O-rings.

 

   Carb sprays don’t damage gaskets and O-rings.  If you’re doing a quick cleaning and get spray on gaskets and O-rings it evaporates so fast there is no effect.   For a bench cleaning or dip those parts are removed and don’t get juiced.

 

   It’s rare to have to pull an emulsion tube on a Tecumseh engine and they never have a problem with spray or dip.

 

   Plastic connectors on some carbs at the gas line carb port get left on during a dip and are never affected. Thye not affected by spray.

 

>>>Seems likely that the cleaner might also damage any rubber seats or needle tips that it comes in contact with.

    Needle tips and seats are usually removed for a bench cleaning or dip.  For a quick spray the spray evaporates so fast there is no affect.
borat


Joined: Nov 10, 2007
Points: 2692

Re: How do you clean your carburator?
Reply #10   Dec 8, 2011 11:08 am
Nothing beats complete disassembly , probing with a thin wire, flushing with a spray of your choice (mine is WD-40) and blowing out with compressed air.   Every possible orifice, hole, gallery, channel, opening and jet must be known to be clear prior to reassembly.   Otherwise, you'll be doing it again until everything is clean.  I've learned that there is no shortcut to a clean carb and I've cleaned a few.
carlb


Joined: Nov 16, 2010
Points: 279

Re: How do you clean your carburator?
Reply #11   Dec 8, 2011 12:21 pm
I learned early on that no stone can remain unturned when cleaning a carb or you will be doing it again and again.  As Boart said disassemble and clean every hole, nook and cranny flush with wd40 or your choice of cleaner and blow every orifice out with compressed air, taking note not to blow the rubber seat for the needle and seat out.
This message was modified Dec 8, 2011 by carlb
RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Re: How do you clean your carburator?
Reply #12   Dec 8, 2011 1:14 pm
When cleaning one for the first time recently, I soaked the carb (minus the plastic and rubber pieces) in a glass jar with Berryman B-12 Chemtool. It was inexpensive, and it was Walmart had for liquid carb cleaner (not sprays). I'd read about some people suggesting using that for soaking them.

Does anyone have experience with how well the B-12 typically works for that application? I think it's meant more as a Seafoam-type fuel additive. But, again, it was just what I had access to while I was at the store.
borat


Joined: Nov 10, 2007
Points: 2692

Re: How do you clean your carburator?
Reply #13   Dec 8, 2011 1:43 pm
RedOctobyr wrote:
When cleaning one for the first time recently, I soaked the carb (minus the plastic and rubber pieces) in a glass jar with Berryman B-12 Chemtool. It was inexpensive, and it was Walmart had for liquid carb cleaner (not sprays). I'd read about some people suggesting using that for soaking them.

Does anyone have experience with how well the B-12 typically works for that application? I think it's meant more as a Seafoam-type fuel additive. But, again, it was just what I had access to while I was at the store.

No experience with B-12. 

I don't expect the fluids I use to do any of the actual cleaning.  Gasoline is a pretty potent solvent.  If it doesn't dissolve it's own residue, I doubt that there is much out there that will be very effective without some form of  physical cleaning.  I would not trust any concoction to clean a carb on its own.  The only reason I use WD-40 is because I keep a supply of it on hand.  I use the fluid not so much for cleaning as much as confirming that the passage/orifice/jet are clear.  When I spray the fluid in one end, I want to see it come out at the other.  That, plus the flushing effect is all I use the fluid for.  The primary cleaner is the piece of thin wire.  I use it to loosen any debris that may be in the passages/orifice/jet then flush and blow with compressed air.  Using a liquid on it's own will not be nearly as effective as probing/flushing and compressed air.
RedOctobyr


Location: Lowell area, MA
Joined: Nov 5, 2011
Points: 282

Re: How do you clean your carburator?
Reply #14   Dec 8, 2011 2:33 pm
To flesh out the thought, yes, I also used a lot of spray carb cleaner, some little picks & hooks (not for jets, just for getting gunk off the carb body, etc), and two different diameters of copper wire, for running through openings and passages. Sprayed carb cleaner through each hole to make sure it came out the other side, and used compressed air as well. The only passage I could not get the wire to go all the way through (coming out the other end) was the idle jet/passage, on the engine side of the throttle plate. I could run the wire into it ~2", starting in the flow path by the throttle plate. And I could get it to go into the hole by the main jet, but I couldn't get it in far at all, just into the hole. I think that passage maybe takes a turn right at the hole, so maybe that's why.

The engine runs now, so this pretty much worked. But it does hunt/surge a bit when sitting with no load (it has no throttle control, it's at 4000 RPM). I understand that could be due to it running lean, or having a partially blocked idle jet/passage. And that's the only one I couldn't really confirm was fully open. The carb is not adjustable at all. I'm not sure that the o-ring between the plastic emulsifier tube and the main jet is sitting where it's supposed to be, it slipped out of its groove while installing it, and is somewhat between the end of the tube, and the top of the main jet. I'm hoping the engine will smooth out when I can put a load on it (today's possible-snow turned out to just be rain).

I soaked it in the hopes that the cleaner could help deal with anything internally, which I couldn't really reach (such as the idle jet/passage).
Replies: 5 - 14 of 19Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42