Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Hi all,

I just bought a 1993 (I think?) Ariens ST824. Model 924082, serial 0040XX.

The good news: Paid $150, the augers weren't turning (the belt had come off, and seems like it needs to be replaced). It starts & runs fine, and has electric start. The engine showed ~120-130 psi when cranking it with the electric starter, and ~60 psi when pulling it by hand (I don't know whether those are good or bad). It has a differential, rather than the simple pin-through-the-axle setup of my MTD. I thought that was a cool surprise, I didn't expect a differential. Is that common on the ST824's, or did I get lucky? The differential works fine. It's a weird feeling being able to just steer it.  I get the impression that the previous owner gave it some grease occasionally, since the gearbox area seems well lubricated. The person I bought it from just got it recently, so I don't know its history.

The less-good news: It has a fair bit of rust, unfortunately (may have been stored outside?). But it seems solid. There are two areas that concern me so far.

One is that the big gear on the differential can skip against the teeth of the mating sprocket. There appears to be quite a bit of play in the wheel bearing on that side (the bearing at the other end of the shaft, for the right wheel, seems a bit better). So I think the shaft is being allowed to move too far away from the mating sprocket, and it's able to skip. Is this common? It looks to me like replacing the wheel bearing should do quite a bit to help make the gears tight again. Am I right? Is that a difficult job? Special tools needed, etc? It sounds like a tapered roll pin has to come out, from glancing at the service manual. 

The other issue is that there is play between the two halves of the unit. The tractor half, and the snowblower half. The big bolts at the top of the frame, which join the two, were loose, and able to bang back & forth. It seems that it's been used like that for a while now, unfortunately. One of those bolts can't be tightened, the nut (below the frame) just spins. I'm having a hard time figuring out a part number for that nut. As a result of those bolts being loose, I assume, the bottom area, where the two halves join, has also worn. There is a rod in the tractor half which slips into a groove in the snow blower half. That groove has opened (I think) and the rod has worn smaller. So there is play down there as well. I'm not sure if there's a good way to try and take up that play, with some kind of bushing perhaps.

So I think I need at least some belts, a friction disk, probably one wheel bearing (I'd prefer to leave the right-side one alone, if possible), and I'm sure some other random parts. Maybe I can figure out some way to tighten up that rod-to-groove fit at the bottom.

Does this sound like it's worth fixing up? I'm looking for something reliable and durable to replace my MTD 8 hp, 26". I just don't know whether the issues described above should really never happen, and therefore this machine has been put through a LOT. And that maybe I should look for a different one. I don't have a problem fixing this stuff, as long as a handy homeowner can replace the bearing, and so on. I just don't want to start down a rabbit hole.

Thank you for any feedback or suggestions!

Looks like he summed up what I was trying to post last night when my internet decided to quit working.

In addition to the axle bearings, check the bushings on the sprocket that mates to the differential gear.  Those are part # 05502600 and needed to be replaced on mine.  The axle bearings aren't too bad to replace.  The whole axle needs to come out.  Remove the tire on the side with the differential lock, then use a pin punch to knock the pin out of the differential lock.  The pin might be tapered so if it doesn't go out one way turn it around and try to drive it the other way.  That will let you pull that side of the axle out.  Now you need to knock the pin out of the main axle from under the frame.  If you are taking it apart you might as well replace both axle bearings.  Might replace the bushings in the outer axle too if you are trying to tighten everything up.  Ariens is probably going to charge an arm and a leg for the bearings and you can probably get them cheaper from a bearing supply place.  Looks like part # 05417700 for the axle bearing.

I wouldn't worry too much about the play in the front end.  Just tighten it up and see how it works.  If you have a tap and die set you could just drill it out and put a bigger bolt in it.

Also pull the shear pins and make sure the rakes are not rusted to the shaft in the front.  If all is good grease them up and check the bushings on the ends and the impeller bearing in the back up there.

The good thing about the old Ariens is little changed over the years so a lot of parts can interchange.  Find yourself a couple old neglected blowers for dirt cheap and you will have lots of spare parts.

Guys,

Thank you very much for the help, I really appreciate it. I ordered some belts, a friction disk, 2 wheel/axle bearings, 2 of the bushings for the sprocket shaft, 2 of those Nut Retainers, some of the R3 auger gearbox grease, etc. The name and part number of those nut retainers was a big help, by the way, thanks!

I hope the new bearings will snug up the mesh between the two gears by enough to make them work properly again. I'd prefer to avoid replacing that sprocket if possible.

I was thinking about how to snug up the fit between that rod and the groove in the other half of the frame. I don't have the machine in front of me at the moment (traveling). But it seems like maybe I could mate the two halves of the frame securely, by standing it on the auger housing (wheels in the air). Then drill a hole through both frames, in one location on each side. Then put a bolt through both holes. Maybe use a shoulder bolt, so it will be held through the frames by a solid rod, rather than shearing sideways against the threads on the bolt. To remove the bolts, I'd need to remove the transmission cover, so that I could hold the nut that would be on the inside of the frame. But that's not a big deal, given how often I should have to split the frame. I don't have a welder, by the way.

I felt the impeller bearing the other day, it *seemed* OK, I did not notice any play in it. I need to look up what grease and oil are recommended for other items besides the gearbox. I need to change the engine oil, probably to 5W-30 Mobil 1, like I use in my current snowblower. And I may try lining the inside of the chute with plastic, as has been mentioned here. That seems like a pretty clever idea. I have to admit, the plastic chute on my MTD works very nicely, and nothing sticks to it. I may also try the Clarence impeller kit (haven't checked the impeller/housing gap on this one yet). But that's a very clever kit.

Got to do some more work on it tonight. Checked the auger gearbox oil level, using the test in the manual (raise the back 6", etc). It passed the test, has enough oil to wet the fill plug again. The augers each appear to be able to move on the auger shaft, and are not rusted in-place.

I removed both wheels and the axle. Drove out the roll pin by the right wheel. The bearings were quite worn, there is a lot of play in them. When I removed the left wheel, and went to remove the differential lock assembly, I found that the 1/4-20 grade 8 bolt, which holds it in place, had previously broken in half. I did not see any roll pins in that area that I had to remove. After sliding out the broken bolt, that differential knob assembly slid off. I have not tried to open it (have no need to).

I'm letting some PB Blaster sit on the nuts that hold the Bearing Retainers in place. I wish they had something besides flat-blade screwdriver heads on them. Very awkward to reach and hold. Now I'm waiting for the replacement bearings, etc, to ship.

Those flat head screws on the back of the bearing retainers "should" hold themselves in place.  They have little ribs on them that push into the frame similar to how wheel studs on an automobile are.  The auger bushings up front have the same type of screws on the inside.  That being said, a couple of mine were loose enough that a screwdriver was needed.

Sometimes people take of the locking hub loose the pin and put a bolt in it's place.  The pin for the hub is a solid pin.  Not a roll pin.  The bolt will work, but I would
go ahead and order a pin.  It holds the hub onto the shaft with a much snugger fit. 
Those small bolts can be a pain if they have lost their self holding power in the frame.  The good thing is once you get your new bearings installed those bolts won't
have to come out again for a long time.

Hmmm, OK. The screws that hold the bearing retainers might stay put. But I tried one last night, turned the nut, and the screw head turned as well. Tried to hold it with a screwdriver, tried again, and the screw turned again. Maybe the others will stay in-place, I don't know. If they all try and turn in the frame, is there a reason I couldn't replace them with hex heads, once they're out? At least I could hold those with a box end wrench.

On the note of the pin/bolt, maybe I didn't explain it well. I'm referring to a bolt that goes perpendicular to the axle shaft, and holds the Lockout Hub in place. It would keep it from sliding off the shaft when you go to pull the knob for locking/unlocking the differential. It's shown in the Parts Manual for 924082, as Item 42, in the Reduction Drive section, described as 1/4-20x2" cap screw, grade 8. I'm not referring to the spring-loaded pin that slips into the hub, to lock the differential.

I do see an Item 38, Bshg-Slv, listed on the drawing. I don't *recall* noticing something like that last night. Where does that bushing go? It's shown between the differential and the left-hand axle. Might it have stayed in with the bearing? I just want to make sure I'm not somehow missing a part. There is some wear on the axles where the bearings sit, unfortunately. I will try them as-is with the new bearings, since I don't want to go too crazy with just replacing everything. Thank you again for all the help.

Some models used bushings and some used bearings for the axles.  Most of the parts lists are for multiple models so they just show both parts.  That being said, there are 2 small bushings on the short side hub axle where the 2 pieces slide over each other.  These are pressed in pretty tight though as I had some trouble getting mine out to replace.  You probably could use hex bolts in place of the screws, however, I believe they will stick out too far on the side with the differential gear.  I think to remove one of my screws I had to hold the screw with the screwdriver at a 90 degree angle so instead of using the tip of the screwdriver I was actually using the side of it.

Keep in mind that mine is a 1977 model and probably a little different.

RedOctobyr wrote:  As was already stated, a regular bolt won't work because of the clearance issue with the diff.  You could try using allen cap head bolts.  They have a head that isn't as tall as
a hex head bolt.  What I have done in the past when I've had the issue with the heads spinning.  Was to remove the four bolts.  Clean the threads real well, make sure the
the nuts spin on without any effort.  Put the bolts back in and start tighten down the nuts.  Sometimes when they go back in the holes in a little different position.  They will grab in the holes once again just enough to allow the head to come in contact with the steel frame. And if you hold the heads with the screw driver.  They will tighten down fine without spinning the heads.

Sorry about the misinformation.  Yours is supposed to have a bolt holding the locking hub on the axle.  Mine which I guess is older uses a pin.

There are bushing inside both ends of the left hand short axle/housing. Slide it on the axle half way, (locking hub end first) and see if it's sloppy on the shaft. 
Then slide it on half way (correct end first) and see if it's sloppy on the shaft.  Hope that makes sense?

Tried the rest of the bearing flange screws. 3 came off (the screws stayed put, held into the frame). The other 5 just spun :) I managed to get one of them off, using a 90-degree screwdriver. The others will all probably be Dremeled off. If I can find maybe some button head socket cap screws, or possibly low head socket cap screws, I might try to install those as replacements. At least I could hold the screws with an Allen wrench, vs a screwdriver :) If the threads weren't so rusted up, they probably would have come off OK. Removed one axle bearing, it is a sloppy, worn-out mess.

I looked a bit at bushings on the axle. The outside end of the left axle is snug, when I install it backwards. It also felt OK when installed normally. I didn't dig around in the grease on the inside of the left axle, trying to see if I could find a hidden bushing buried in there :)

I have to say, the grease fittings seem to be a big help. Much of what I've tried to remove, if it's not exposed threads, has been lubricated, and came off OK. This may be my only piece of OPE with grease fittings (my Craftsman tractor might have a one or two); it's a nice feature. I'm hoping to find some good, suitable grease, which won't get too solid/sticky at low temperatures. I've seen marine and snowmobile greases mentioned. I found marine grease at Lowes. Not sure where to find snowmobile grease, or something else that's meant for low temperatures. I've used wheel bearing grease on my MTD (it's what I had), on the shaft that the friction disk slides on. That must be too sticky, because the shifter lever is quite stiff on that one, by comparison, and the grease feels tacky on the shaft.

RedOctobyr wrote:
Yea those little bolts for the bearing flanges can be a pain.  And your right, it's the rust that messes things up  I know Ace Hardware carries allen cap bolts. I've bought them there before. I wouldn't even be surprised if
you could find replacement bolts as well.  Ace Hardware has an amazing assortment of specialty nuts, bolts and small hardware.  The best I've ever run across.

A black moly grease works pretty well for the axles.  On the shaft for the friction disk slide, I guess you talking about the hex shaped one?.
 I always spray some carb cleaner on a rag and clean off the shaft real well.  Doing that alone will make the thing slide easily.  Just a light coat of white litium or even the
moly grease will work.  Your right, axle grease is too thick and sticky.  Just don't put much on it, just a light coat.  The shaft spins pretty fast and if the lube slings off it can get on the friction drive disk.  Not good.  Your going to have a nice blower when your finished.  All the parts your replacing are probably original.  So they lasted what 20+ years.  That's pretty good.