Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

It's in decent condition, new rubber impeller, scraper bar and overall good shape. The guy I bought it from said it had been professionally serviced 2 years ago but had seen little use since then as he decided to hire a plow guy to do his average residential driveway. I could not get it to start after adding some fresh fuel that I brought with me so I offered him $ 40.00 and said OK. - he had it listed for $ 75.00 on CL. I'm pretty sure he left some old, unstabilized fuel in there and it turned into varnish.

I removed the top and back covers and dropped the fuel bowl. It looked like a bad batch of applesauce in there so I cleaned it out and shot the carb with carb cleaner and reinstalled the bowl. It fired up for a few seconds and then died. A good carb cleaning appears to be in order and I'm wondering if I can do this with the carb installed or is it easier/better to remove it from the engine (Suzuki 47P)? I've never removed a carb before but am mechanically inclined and would like to get this operational for next winter.

I remember Borat discussing a cleaning of the jets using wires to remove any build up inside that could cause fuel starvation. I have never done this so any suggestions or tips will be very much appreciated.

borat wrote:

This sounds like the arrangement that I have on this engine. I will remove the main jet and thoroughly clean as suggested. I've been able to get it running for about a minute after several attempts using edgenets suggestion of a teaspoon of gas down the spark plug hole.

I appreciate all your input and know that I will get this fixed with your help.

Thank you!

Frank 

Well I have been working on this off & on for a few days now and still can't seem to keep her running for very long. She'll turn over and run sometimes for up to a minute or so and other times just for a few seconds. I've cleaned the carb as suggested by borat (it was exactly as you said it would be) and hosed everything down with carb cleaner. This really seemed to remove a lot of garbage, especially when I removed the float and needle and gave it a good blast of carb cleaner. I'm going to give it another good cleaning, reassemble everything and see if this does the trick. I'm getting there slowly - any other suggestions are welcome.Thanks again for your help. 

Frank- Change the fuel line which may have deteriorated and flush the tank. While you are at it if there is room I would install a fuel shut off valve.

Marc 

mml4 wrote:

Thanks Marc. All of the above is going to be my next step. I noticed the fuel line looked a little suspect when I replaced the fuel filter but did not have the correct size fuel hose to replace it with at the time. Off to get some parts and will hopefully have some good news to report later.

Have you removed the carb to clean it?  If not, you should.  There are some very tiny holes in the carb venturi that need the wire treatment and flush. 

With intermittent running, it sounds like you have fuelus interruptus.  

Start at the fuel tank.  Take a good look inside for dirt or take it off the machine and flush it out.  Closely inspect for an interior fuel filter (probably not) and make sure the fuel system from the tank is clear.  A new fuel line won't hurt.  Once you know you have positive fuel flow to the carb, you can then concentrate on the fuel systems inside the carb.  Can you tell if the engine is either starving or flooding?   If it's flooding, your float might be defective.  If it's starving, I suspect it's the very fine orifices and/or galleries within the carb.   Taking it off, cleaning with very thin flexible wire, flushing with WD-40/carb cleaner then blowing out with compressed air should get it running right.  

Keep us posted on how it goes.

  Pulling the carb should be easy.   If I remember right the carb on those are on standoffs and have just enough governor rod length to allow it to slip over the studs.   Given the appesauce a dip might be helpful ($20 for Berrymans at Autozone).  The float level could be messed up.  

l would install a new needle and seat, just to rule out that its not sticking closed and starving the engine of fuel, but most imporantly l would make sure the FLOAT is adjusted properly and not sitting too low in the bowl. make sure its level with carb base when upside down.

Well here is where I'm at with this project. I've replaced the fuel filter, fuel line, primer bulb (it was missing) and feed line, drained and cleaned the fuel tank, new spark plug, cleaned the carb several times and replaced the float bowl gasket. The engine will run for a few seconds and then die, afterwhich I cannot get it started again. I continue to find debris in the float bowl when it's removed for inspection after each failure to start. I replaced the float bowl gasket after finding that it was stretched out enough to not seal the bowl - thought I had my fix after finding this but it still won't stay running.

I'm thinking that if I just keep at it and maybe add some fuel in the spark plug hole, that it will eventually flush out whatever debris is causing the problem. I'm also thinking that trouts and borat are correct in suggesting that I drop the carb and give it a thorough cleaning and a dip in some Berryman's - maybe even replace it if neccessary. I'm only into this for about $ 60.00 at this point so I'm far away from the point of no return. The teaspoon of fuel in the spark plug hole has produced that best results in terms of run time - up to about a minute before it died. 

Do you think I should keep trying to get it running via the teaspoon of fuel method and possibly flush out the problem (pun intended) or drop the carb and clean with wires and a Berryman's dip? Where are the holes/jets located that I should clean with a wire? I did remove and clean the jet located inside the main jet orifice, dropped the float and needle, cleaned both and reassembled and have spayed the entire carb inside and out with copius amounts of carb cleaner.

Where could the dirt and debris be coming from if you cleaned the fuel tank and replaced line and filter?  Can't get my head around that.  You have to determine where the dirt is coming from.

If the engine runs with fuel dumped into the cylinder, it appears that the engine is experiencing fuel starvation.

Pull the carb off.  Get a very thin piece of wire about the size of a stripped trash bag tie wrap.

Look into the big hole of the carb throat (venturi).  Look very closely on the bottom for a very tiny hole(s) just a bit bigger than the diameter of the wire feed the wire into it to clear it.  Remove the main and pilot jets.  The pilot should be a small brass insert with a slot in it somewhere beside the main jet location.  Try to feed the wire in there and flush with WD-40.  If you have compressed air, use a rubber tipped adapter on the air nozzle to make a seal.  With the jets removed, blow air into the main and pilot jet holes.  Flush with WD-40 and blow some more.  Look for air/oil to come through that tiny hole in the venturi.   Make sure to carefully remove the float assembly before doing any of the above.  Once the carb is properly cleaned, it should run like a top.

Frank >>>I continue to find debris in the float bowl. Often there is crud in the tank and it's screen defective or the line no good and particles breaking off the line. Pull the line at the carb and run water through the tank or gas to a container and run that through several times. Once there were some sort of grubs in the line or tank that died. The carb would be cleaned and the bowl would later get crapped up. This happened a couple of times. The gas would soften them and they would break up into small particles which got into the bowl.