Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Hello all,

So i purchased an almost new (like 4 months old) Ariens Deluxe 30 for only $500 this weekend from someone. It's vitually in perfect shape with almost no signs of wear.   Downside, can't get it to start.  I think it's because the starting key is missing.  Can someone tell me what this key is suppose to look like?  The slot for the key isn't a normal slot I shaped slot.  Instead, it looks like a capital I (or I guess a wide "H" on it's side) shaped slot (see below for crude illustration).  It's currently in the "up/verticle" position.  The engine is a Briggs and Stratton Snow Series 1450.  Can someone help me out and tell what this key is suppose to look like?  Does anyone know of anything like a key with an I shape?  I think that's all it will take to start the engine but not sure.

If no one knows, is there a way to open up the cover and change the position of the switch/key so that I can start the machine anyways?

Thanks in advance for your help.

midfi

Shape and position of slot:

XXXXXXXXXX

          X

          X

          X

          X

          X

XXXXXXXXXX

http://www2.snapfish.com/snapfish/slideshow/AlbumID=6102571009/PictureID=309553840009/a=54605288_54605288/

http://www2.snapfish.com/snapfish/slideshow/AlbumID=6102571009/PictureID=309553841009/a=54605288_54605288/

http://www2.snapfish.com/snapfish/slideshow/AlbumID=6102571009/PictureID=309553842009/a=54605288_54605288/

Here you go, two close-ups at a better angle.

midfiman wrote:

Thanks for posting your pictures!  I couldn't get the pictures to post so I added three links above.  I hope that you guys can see these!  As you can see, the slot is quite different than yours.  Strange!  I would have thought the engine on the Deluxe 28/30 would be almost the same if not identical...

I have your type of key needed for the Deluxe 30.

Thanks Britmti, I appreciate you taking the time to put the pictures up.  Do you know if I should just go into an Ariens dealer and ask for that, or is there part number I should ask for?  I don't have the manuals with this purchase, otherwise I would just look up the part number and order.

Thanks!

midfi

Don't know how these new ones work but in the older Tecunseh models the key inserted kept a set of contacts open so the engine would run. When you pulled the key the contacts closed and shorted the coil to the block preventing spark from reaching the plug. I've replaced some with switches on my Tecumsehs. Not sure where the connections are on the BS engines.

So, i'll be picking up the key today.  Looks like the local dealer near me has it!

I'm very excited hoping that this is all that's needed to get this blower up and running!  That being said, I'm assuming that the following method should be used to start it:

1.  Check to make sure gas/oil is good to go

2.  Turn the infamous key to the starting position (to it's side)

3.  Push the primer 3-4 times

4.  Set the choke to the choke position

5.  Set the engine speed level to slow (or fast, not sure about this one...?)

6.  Pull the cord or press the electric start button

Then what?  If the engine speed bar is on low, do I slowly move it over to fast, or should I first move the choke lever over to run first and then do that?

Then I'm assuming to turn it off I just slide the engine speed lever over to STOP, yes?

And the only difference on a warm engine is that there's no need to choke, yes? 

Thanks again guys.

midfi

You can get the manual online from Ariens.

BriMtl wrote:
http://apache.ariens.com/manuals/04135800_ENG.pdf

Thank you, appreciate the help.