Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

OK, my snowblower has a Tecumseh engine, so when I read this I thought it could be either BS, correct, or old news.

You can't go wrong with a Briggs and Stratton engine. Tecumseh engines are prone to throwing piston rods through the crankcase wall if the oil level drops at all. The Tecumseh speed control is not nearly as robust as the Briggs and Stratton either. Briggs & Stratton is now back in the snow blower engine business in a big way with overhead valve engines ranging from 6.5 through 13 horsepower. Given prices, contracts and market inertia it's anybody's guess how quickly they will regain market share. However if you shop around machines can be found with these engines.

Anyone with any knowledge care to comment?  Here's the link.
http://home.gwi.net/~spectrum/snowbuying.html


--SnowRemover

Could it be possible Tecumseh's use oil faster, thus catching more people with low oil, thus more kabooms?

Marshall,
Briggs tells me that thier 10 hp, horizontal shaft, L-heads, (that they used on a lot  of generators) use 1 oz. of oil per hr.....That's acceptable too them.
So... say you are on a jobsite....where you run 8 hrs a day....burning 8 oz of oil is normal? I just hope you have an oil-guard switch that shuts it down every couple of hours? Cause if you didnt buy that option.....you are going too have toast for lunch  the second day it's on the jobsite.  I have seen alot of those with big ole gapping holes in the side of thier crankcases.

buttlint wrote: That's an insane amount of oil for an engine to use.  Glad I'm looking for a Honda powered generator with their 11 HP OHV engine. 

buttlint wrote: Their either scewing with you or, more likely, those engines that do run all day have no cylinder walls left and the rings are shot. Who would knowingly continue to use an engine in that shape, besides the government? LMAO

Would this mean that my recycled tec, some parts came from the auto-recycling center
(still love that phrase) will throw a rod in the middle of a dark and stormy night,
(sounds like the start of a novel) snow blowing 2' of snow, so I can get out and get to work.
I keep the oil,(synthetic and a little sea foam) right at the full mark.
Will I have to stop every 1/2 hr. to check the oil?
  WHEN AND IF IT BLOWS IT GOES!!!(right back to the auto-recycling center HA HA)
BUT it will have another tec on it!!
Old iron is good iron!
T.J. terry
 

Recently my Husqvarna Blower went into a high rpm fit seconds after starting.  I had walked away to let it "warm up".

It threw a rod as I was running back to it to shut it down,  This took like 5 seconds.

Not the best idea this day.  It was a tecumseh snow king, 10.5 HP with only about 12 hours on it.  I take care of my stuff like a paranoid mechanic.

It was not low on oil, and had been changed about 2 1/2 run time hours before this happened.  of course it was just outside of warranty.

I just bought another blower with a briggs and stratton engine to get away from this nightmare.  In my lifetime I have never had any of my equipment throw a rod.

Now I have a $1200 boat anchor, and a shiny new Snapper.  Snowing today,  cannot wait to run the new machine.

Maybe I can fit a briggs motor on the Husky?

Jim

I've run two Tecumseh ten horse power L head engines for a total of twenty years and never had a problem with them.  They're not the most  sophisticated engine in the world but they get the job done.  No comparison with the Briggs OHV engines.  Nowhere near as smooth and quiet.  The B&S seems to be quite a bit more powerful for the same rating as well.  

Here's an engine I've rebuilt for my Yamaha RD400.  It's only partially re-assembled.  Carbs & intake system will be taken off before I put it back in the bike.  This motor weighs around 45 to 50 lbs. and should put out around 55 h.p. when all is done.   Put this on your Husqvarna!