Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I bought a tachometer from eBay for $23 including shipping and what a total junk it was (http://cgi.ebay.com/Tachometer-Hour-meter-2-4-Stroke-Small-Engine-Spark-/120689310104?pt=LH_DefaultDomain_0&hash=item1c19a4b998  I got mine from a different seller and was able to get a full refund but what a junk - you can buy a nice bottle of wine for $20 so don't waste your money on this model.

Hey  trouts,

When the temperature goes up a little I will try it on my Honda lawnmower as it has a fixed throttle speed around 2900-3100 rpm.  So if it reads near 2900-3100rpm then the tach is good.    The setting 2 seems to be more reasonable than the setting 3.

I guess the ground wire must make the differance with one of these tachs.You should be set on 2 at all times 3 should not be used at all to see accurate rpm readings.Did you guys look at the lead comeing out of the tach and make sure no white wire is included

under its plastic covering? Who knows there could be one there.With todays light snow i only ran my machine between 3000 and 3200 rpm..I did push some snow to the sides of the driveway to set up a load for the blower.Than i would go to 3600 but even than i would only drop to 3450 or 3500.I find my engine hunts very little.And than its really only when going into a good sized load.I

 must feel the govenor doing its thing for a second or so                                                                                                    a second or so

It is a multi-stranded copper wire without any other electrical wire (i.e., no separate ground wire).  I was able to open the back of the box and thought about adding a ground wire but I do not have schematics for the printed circuit board.  I could find it using fluke meter but it is not that important. 

I have had the back off mine to.I will look tomarrow and see just were the ground wire goes.I will get a picture to

and see if it looks the same as yours ! Although i would think it could go to the ground side of the battery and work?

Relics,

    I'd be interested to know if yours looks the same inside as one MN_Runner posted. 

     The tach was put on the car which has an RPM gage.  The gage was set on 3 and tracked with the car readings over the range of 700 to 3000 rpm.  At first readings around 2000 were ok but lower and higher off by quite a bit.  After about 4 minutes of warmup the readings tracked the car gage. 

   The wire sense lead was wrapped 4 times around the plug wire and taped inplace.  It was also run straight which I think helps.

   The post time is about a half a second after a speed change but seems to take 1-3 seconds for it settle and get a correct reading.  The posted incorrect speeds are always in the right direction and between the reading moved from and the current rpm.  The gage is probably taking several readings and averaging so needs a second or so to get a tight group for the right average after the speed change is complete.

  It did much better than when connected to the snowblower.   Part of the problelm on the blower might have been not having a straight run of wire and the wire field interfearing with itself.  Also, speed changes on a blower engine are not that smooth compared to a car.   

Well here is the inside of my tach which showns the location of the white wire.Which is used as the ground wire on the 2 wire tach.

For some reason? the picture would not post.

Here is the picture !

relics,

Thanks for the picture - I can clearly see the two wires on your circuit board.  I just tried it on my Honda lawnmower and the rpm reading is reasonable.  I was getting 2950-3000 rpm, which is consistent with the manual.  However, the correct RPM reading came at the "2" setting (1 spark every revolution) instead of the expected "3" setting (1 spark every two revolutions).  So my cheap tachometer needs to be at "2" setting to read correct RPM.

2 is the correct setting.Its the same on my old tecumseh 8HP.These engines do fire everytime.As stated already its a waste spark system.So the plug fires every revolution.An for sure your tach is giveing the right rpm.I think the ground wire just makes the tach most likely work slightly better.Maybe a slightly faster refresh rate who knows? But for sure these tachs are accurate.I have used mine for over 8 hrs and its just fine.I find its a real plus to know my rpm.Also running at max rpm i can be sure i am within a safe range and not going above (3600rpm)