Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > Repowered blower test coming tomorrow

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Repowered blower test coming tomorrow
Original Message   Feb 1, 2011 9:49 pm
Well tomorrows the test.  I live in Michigan right on the lake and were getting that storm tonight and tomorrow.  So I expect to wake up to at least 9 to 11" of fresh powder. Ya Hoo...
I repowered my Ariens 1032 with a 11Hp Honda clone (Greyhound).  With the intentions to install a larger blower drive pulley.

Last summer I rebuilt the impeller by adding weld to the end of the blades to decrease the clearance. Lined the blower and impeller housing with stainless steel. Replaced the auger bushings and impeller shaft bearing. The only thing I didn't get a chance to do.  Was to replace the auger shaft bushing setup with flange bearings.  I ran across a pair of 3 bolt flange bearings at an auction.  The bearings were
the right size bore. And the flange looks like it may have the same bolt pattern as the current bushing flange.  Probably won't mess with that change over till spring.
 
I have been using the blower with the stock double groove pulley (2 1/2" drive unit 2 3/4" blower drive) to see how the impeller blade mods. worked out.  Then yesterday I went ahead and installed the larger blower drive pulley.  It's a 3 1/4" pulley which is 1/2" larger than the stock pulley. (by the way I'm now using to separate pulleys not a dual groove)  That should boost the rpm up to 1300 from 1100. 
And increase the tip velocity speed of the impeller blades from 4026 to 4762.
When I started it yesterday and engaged the blower there was for sure a different sound to the blower.  Reminded me a little of the sound of the Honda 928 I had for a while. Sounds like a blower fan.  But with a six bladed 14" impeller it has a deeper sound rather than a whine.

There is a real noticeable difference in the speed of the augers.  Which is good because I have noticed an issue with the blowers ability to clear itself when taking a full 32" wide, bucket height bite of snow.  The slowest speed of the Ariens is still a little to fast for the blower to process the snow.  So you have to pause your forward speed sometimes for just a second or two to let the blower clear.
So, since I can't slow down the speed of the machine.  Speeding up the blower should I hope take care of that issue.

Tomorrow we will find out.  I'm glad it's going to be a light snow. Only bad thing is that the wind is going to be blowing 25 to 30 with gusts up to 40. So snow is going to be blowing everywhere.  Especially with the throwing distance I may now get. 
I do some city sidewalks for a merchant so I'm hoping I can throw all the way across the street.  (Not allowed to throw into the streets).  But with the wind blowing like that
I may just open the chute straight up and let it blow. They'll never know where it can from : )
I'm going to try and shoot some video.  Put by camera in a freezer bag and on a clamp mount right next to the left handle bar.  We'll see, Maybe well see. With that much wind and snow might not see anything but white.

Forgot, I also added these.  We'll see how they work as well

     
This message was modified Feb 1, 2011 by jrtrebor
Replies: 8 - 8 of 8Next page of topicsPreviousAllView as Outline
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: Repowered blower test coming tomorrow
Reply #8   Feb 2, 2011 9:06 pm
trout2 thanks for posting the data figures on the engines and blower rpms.
No I haven't ever tried to calculate the ground speed.

We had a lot of wind with this storm so a lot of drifting. I do a lot of city residential sidewalks in the downtown area so people can walk.  We already had between 2 and 3' of snow on the ground.  So all of the corridors a had previously cut and created filled in with all of the snow and wind we had.  Today (starting at 5:00 AM) I probably spent 5 to 6 hours off and on blowing deep fairly dense, deep snow.  
Quite often I had 8 to 10" of snow coming over the top of my bucket which is 22" tall. I don't think I was into anything less than 18"  the whole time I was out.  If I hadn't put on the larger blower drive pulley yesterday I probably would have had a much more difficult, and time consuming time of it.  Considering the conditions and snow load I have to say that the blower performed really well.  It actually has a very nice sound to it.  The motor and the blower sounds seem to kind of resonate with each other. 

I did still have to feather the forward speed with short pauses.  But considering the amount of snow I was trying to clear with a 32" bucket I'm fairly satisfied with the blowers performance.  I think when blowing a more moderate 8 to 12" snow that the forward speed won't be a problem any more.  The chute shields I installed work well didn't have snow beating on the side of my light housing with the chute
turned full to the right.

This morning It was still dark. Wind was blowing 25 to 30 snowing like crazy blowing everywhere.  And I'm thinking am I going to be able to get through this as the snow is rolling over the top of the blower.
Sometimes almost blocking my light. I've got a rooster tail going twenty feet in the air and the wind is blowing it across a two lane street in the opposite direction I was blowing it. It was kind of surreal. 
But everything held together including my hands which got a work out just holding onto the blower and keeping it going in the right direction. When you could see well enough to know which way that was.

I'm definitely going to see if there is some way to retrofit one of the old style Ariens control units to my blower.  I had one on my old 724 and I loved it.  It has two heavy duty handles one for the auger engage
and the other is the speed control.  It was so nice to just be able to engage the augers with a handle and not have to hold down a lever.  You could also disengage without having to stop of even slow down
your forward motion. They have a large button on top which locks and unlocks the levers movement.  There sturdy and precise. Great controls.


 I really would be satisfied with just the auger engage.
That would leave my left hand free to operate the joy stick control for the chute.  Now I have to keep my thumb in the right position to operate the joy stick while at the same time keep my hand in position to operate the auger lever and hold on to the blower. Have to think about that tomorrow. It sure would make things easier. 
Well I'm going to take a shower and go to bed.  I'm beat after a great day blowing snow which ended with the sun shining. 
Can't beat that especially since nothing broke, bent or blew up.
This message was modified Feb 2, 2011 by jrtrebor
Replies: 8 - 8 of 8Next page of topicsPreviousAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42