Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

After one snow storm the chute on my 3650 is very hard to turn.

I took everything apart thinking that sand and salt must be the problem but everything is clean.  With the top shroud off the chute turns easily.  With the shroud on it becomes hard to turn.  I believe the problem is the friction of the chute turning against the rubber gasket on the top shroud.  The gasket is probably there to keep snow from entering the engine area.

I tried using a silicone stick lubricant on the gasket and this helped a little but it is still very hard to turn.

Any ideas?

Emmo:

I don't understand why the drag didn't appear for a few days in both of our cases but it sounds like the same issue.  Dr. Lints diagnosis was right on and seemed to solve the problem.

Hope your 3650 makes a speedy recovery.

I have been meaning to ask about the 3650..  I think I own its predacessor/clone.  A 1988/1989 toro ccr2000.  I think it is the first year they came out with the power curve auger  etc   4.5  either suzi or kaw engine.  Not sure as I have never had to touch it cept for putting in a plug or two.  Have prob over 500 hours on it.  The thing will not quit,  throws like a small two stage, (not unlikely to get 35 feet  throw in powder) still looks new.  i was going to disassemble last year for a refurb etc.  didn't get to it.   It does 4 or five properties every snowfall.   

So I will need a new one soon as my 15 yr old uses this one to do neighborhood.

I  am sure the 3650 is a much better machine,  but can I assume they are both built on the same platform.  A better way to say that is are they almost alike.  15 years is a long time so if they made a good thing better then I will be more inclined to buy one before mine gets beyond repair or if a lot of the basics are the same and most ccr2000's were dependable like mine, I will search harded for a used one.  I have seen a couple on e-bay but they usually seem to get a real high price.  Last two went for like 275plus 50 shipping, (at a dealer in 89 they went for 425, I paid 350 end of year price)  one of which said was only 8 yrs old. so guess I can assume they made them for at least 8 years.  

Ben07

Hate to bring this one back but another snow storm and the chute is again binding!   

The gear lash adjustment and some spray lube on the chute seems to work fine; until I actually throw some snow. 

Its not like I am turning the crank that often based on the way I clear the drive.  Maybe 5 times max while doing the EOD.  Aside from this symptom the blower is great.

Since I have had the blower for about 2 months seems like a trip to the dealer is a good idea before the warranty slips away.

Anyone else seeing the same thing?

 TomP

If that blower is still under warrenty, I would take it to the dealer (when winter blowing is over) and let Toro fix it !!!

                                                              Fred

Tom,

It still hasn't happened to me.  I will get another run tonight, had one earlier this week, and maybe if we get a storm on monday.  I do use the crank often when doing my drive.

I'll keep you posted.

Regards,

Walt

By all means guys,
Bring them in too the dealer and have them checked out if you are having a problem.
This is a good time too do it.....things are slow in the shops (unless we have another big storm) and there is usually a quick turn-around at this time of year.
We are all stilled geared into snowblowers and looking for excuses too write warrenty claims.
You will get much better service now...than you will in mid-July.
Why?......Because in the middle of mower season all memories of snowblowers will have been deleted from our memory banks and the blower will be shoved off into a corner, much like lawnmowers are at this time of year.