Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > How to adjust a Honda chute hood deflector?

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

How to adjust a Honda chute hood deflector?
Original Message   Jan 12, 2011 9:09 pm
For an HS828 hydro factory # SZAK 201xxxxx  The chute hood keeps riding up several second after setting it low.  The hood has nut and bolt on each side.  The stick control lever is pretty loose in that it is easy to move up and down.  Is the just to tighten the bolts more or is it done from under the dash? 
Replies: 1 - 5 of 5View as Outline
MN_Runner


Location: St. Paul, Minnesota
Joined: Dec 5, 2010
Points: 622

Re: How to adjust a Honda chute hood deflector?
Reply #1   Jan 12, 2011 9:20 pm
trouts,

I don't have this problem yet but definitely interested in how it is resolved.  I would try tightening the bolts on the hood to increase friction so the chute is not easily moved up due to snow deflection force.  Just a suggestion.

tkrotchko


Location: Maryland
Joined: Feb 9, 2010
Points: 143

Re: How to adjust a Honda chute hood deflector?
Reply #2   Jan 12, 2011 9:21 pm
The manual doesn't address looseness, but on page 3-5 it says to adjust the chute guide (what you call the hood deflector) with the adjusting nut which is just beyond the panel (I hope that makes sense) and you do that while the chute is in the most raised position and the lever is in the UP position. Then it says to "loosen the nuts on the chute guide lever stop, then lower the chute guide to the position where the clearance between the chute guide and chute is 1-3mm (0.04-0.12 in). What I take that to mean is that the nuts on the chute guide itself determine how tight or loose the chute is, but you have to adjust the slack in the cable to get the full articulation of the chute/hood
jrtrebor


Location: Michigan - 3 hours north of Chicago on the lake
Joined: Feb 10, 2010
Points: 539

Re: How to adjust a Honda chute hood deflector?
Reply #3   Jan 12, 2011 9:24 pm
You may need to adjust both.  The lock nuts on the deflector itself.  And the friction adjustment nut at the handle.  You might also check to make sure that the cable housing / sheath is not pulled to tight. Because the threaded portion on the end of the cables is screwed out to much / to far.  If they are they will put tension on the friction assembly. It sounds to me like maybe the cable length needs to be adjusted and maybe a little more friction.
This message was modified Jan 12, 2011 by jrtrebor
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: How to adjust a Honda chute hood deflector?
Reply #4   Jan 12, 2011 10:06 pm
OK, thanks guys.  I'll give it a shot tomorrow morning.
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: How to adjust a Honda chute hood deflector?
Reply #5   Jan 13, 2011 8:58 pm
    Checked the hood operation with the other machines and it looks like the hood stays fairly loose.  I was going to try adjusting the nuts but one side had a nut stripped so could not be tightened or loosened.  I sawzalled it off.  That exposed a collar around the bolt.  I think that's to keep the nut and bolt from tightening too much.  So I went to the under dash part.

   The nut and bolt through the lever guts was very tight.  To get it tighter I had to really crank down on the nut.  That made the hood work correctly and not rise when tossing.  Cool, but with cranking so hard to get it to work something must be wrong or worn.  It's working for now so I'll just use it like that and get back to it in the spring with better weather.

This message was modified Jan 13, 2011 by trouts2
Replies: 1 - 5 of 5View as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42