Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I am considering replacing my Ariens 926 snowblower with possilby a Honda.  I want a better motor and something that is going to tackle the plowed driveway a little better.  I think if I could get a Subaru motor on a larger size Ariens, I would still consider one but they only offer it on the smaller compact model.  Anyway, I can't make up my mind on a tracked model or wheeled model honda.  I live in Wisconsin and have a 3 car wide driveway and sidewalk to do.  Will the tracked unit clear down to the cement or do I have to shovel the little bit it leaves behind after blowing?  Also, would I be able to turn 180 degrees when I get to the end of my sidewalk with the tracked unit or would I have to make my turn in the driveway because I may need more room to make a turn on about a 4 foot wide sidewalk?  Probably still have to do that with a wheeled unit anyway.  I've head a few people state that the tracked unit moves a little easier when you have a little bit of snow under the track but since I have a concrete drive, I may not have that little bit extra to easy the turn.  I really would like to try one out but most all of the dealers around here don't stock the two stage only the single stage.  I would assume because of price and low sales on the larger units.  I saw a used HS1230TA from about 2004 for $2500 but feel that might be too big.  It looks like new and only has about 4 hours of use.  Any advice would be greatly appreciated.

Thank you,

John 

The 926 Ariens has a good power to auger width ratio and shouldn't lack "oomph". Perhaps the carb is set below the 3600rpm level. I bought a Toro Professional grade mulching Lawn Mower with a 6hp. Kawi a number of years ago that didn't mulch the grass very well at all.  I put a tach on it and found the engine was turning about 3050 rpm. I adjusted up to 3550 and it made all the difference in the world.

I spoke to the dealer who told me that the engine manufacturers usually set the engines below the 3600 mark.

With regard to the riding up issue -Have you tried a weight kit? Very few people do but in my experience they are very effective. I had an old paddle wheel Simplicity which had a rather long wheel base and small tires .It rode up badly at the EOD till I bolted on a weight kit.

Marc 

lseap107 wrote:
Someone recommended the 26" 8hp Toro 826OXE.   While it's a fine machine, and I like the dual sbowblower approach, I don't see it providing a better motor or better performance for EOD plowed snow over what you currently own.  Same 26 inch bucket as your Ariens and one less hp.  

The 9hp Honda engine would likely be better than the 9hp on your current Ariens but would it be more powerful than a 342cc Briggs?  

The best way to handle plowed snow always seems to lead to trade-offs.  In my opinion plowed snow became more of an issue when manufacturers went away from tires that needed chains.  Back in the 70's if your machine had enough overall weight plus chains on the tires it would plow through anything.  Today's SnowHog type chainless tires are good on snow but will lose traction on icy snow.  So to solve the loss of traction problem, manufacturers didn't go back to chains, they built machines with tracks...which in turn created maneuverability problems.  One would expect the tracked Honda to provide an improvement with deep plowed snow but is that the machine you want to wrestle with to clear a small 3 inch snowfall.

So there's no perfect answer.  Just for giggles though if I were you I'd try fitting the Ariens with appropriate tire chains and see how it does.

Also, has an aside, the augers on older snow throwers were positioned so that they protruded in front of the bucket sides by six inches or so.  Nothing by speculation on my part but I think that aided in breaking up packed snow better than todays design.  Today the augers are positioned well back inside the buckets.  My guess is that the change was made for safety and liability reasons.  The mega blowers, the one's attached to semi tractor-trailer cabs, still have the augers well in front of the housing. 

Thank you all for the informative answers to my question.  I think I am leaning towards the Honda.  I was set on going with the HS928TAS tracked unit but my dealer said he would sell me the HS1132TA tracked unit with electric start for $205 more.  Should I go with the bigger 11hp 32" cut or just stay with the 9hp 28" cut?  My driveway is 38' x 38'.  I have a three car garage with sidwalk.  Any suggestons?

I would go with the HS1132TA, but I think the electric start is money thrown out the window, since these machines start on the first pull all the time.

I used my new HS928TA and I love it, again starts on the first pull.

lseap107 wrote:
Sounds like your dealer is trying to move that 1132 since there is only a price differential of $205 from a 928.  I would suggest go with a 928 and try to negotiate in commercial side skids or a light kit if it doesn't already have one.

kderobertis wrote:
It does start easily without electric start.  The price for electric start has gotten ridiculous.  I'm glad I got mine when it was just $100.

I have a snow cab on mine so I'm having electric start is nice.  Some day, I'm going to rig up a battery so I don't have to get out of the cab to get it started.  :)

If your only going to have one machine, I would go for the HS928TA - big enough to get the job done but small enough to be a bit more manueverable. Not saying anything bad about the 1132 but it is a big machine and your requirements seem better suited to something in the 28" bucket range or slightly less. You'll never use the electric start (nor will you need to) so count that out of your decision making process. I know this goes against all the unwritten OPE laws of equipment buying, but sometimes you can get a machine that's too big. Buyers remorse is a terrible thing....

Sounds like the 928 then.  I, agree I don't need the electric start but he has it on both of the 928 units already installed. 

Both the HS928TA or HS1132TA would work fine, you can't go wrong either way.