Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I'm hoping I can get some help from this forum....or at least your opinion.  Three years ago when I was transferred to Connecticut, I purchased an old (mid 70's, model 910995) ariens snowblower that I found on craiglslist.  The purchase was alittle bit nostalgic, as it was very similar to the machine my dad had and used all while I was growing up, and worked great for him.  For the past three years, no problems....quick to start up, and threw the snow with ease (even the heavy crap we sometimes get in CT).  This fall, I changed the engine and gear oil, filled up with fresh gas, and gave the carb a couple of shots of cleaner while I let it run.  It ran for about 15 minutes with no problem and I was confident it would be another good season.  During the big snowstorm we got over Christmas, it did not go well.  The blower worked for about 10 minutes with no problems, then shut down.  No sputtering, or sounding like it was running out of gas, just died. I restarted it with no problem, and it ran another 5 minutes, then the same thing....died.  I continued to clear the driveway like this, a couple of minutes of running, then die, then restart.  Sometimes it would die when under a heavy load, other times not. 

So a couple of questions:

     -Any suggestions on what I can do to improve/fix this problem?  The way it runs fine, then shuts down without warning, then restarts easily makes me think its more spark then fuel related.  Any thoughts?  I haven't done much work on small engine other than the normal mainenance, but am reasonably mechanically inclined. 

    -Unfortunately, I have no way to bring the blower to a repair shop.  My local shop will pickup/dropoff for $75.  Add in another $100 or so minimum to repair, and I've spent close to 200, and still have a 30 year old engine.  Looking online, I can get a replacement motor that I could put in for about 250.  Doesn't this make the most sense?  I'm pretty confident I can swap out the old engine, less confident of my troubleshooting/repair abilities. 

Thanks for reading, and appreciate any advice.

Loosen your fuel cap to allow air into the fuel tank while it's running and see if the problem goes away. 

If the machine has points and condenser, you may have a bad condenser if it's not fuel related.  A faulty condenser will work until it heats up then it shuts down.

Thanks for the replies and suggestions so far.  I was aware of the issue with the fuel cap, so I loosened it after first time it died.  No key on the blower to kill the engine, but I'll look it over to make sure nothing else that could shut it off. 

I got the manual off the internet, and will start checking out the rest of the things.  I forgot to mention in my originial post, the compression was 80psi when I checked it dry.

Thanks again

Could it be a carb problem?

Like something loose in the bowl that occasionally vibrates over and clogs the jets.

Or a stuck float getting stuck closed sometimes.

Or while we are at it something in the bottom of the tank.

Shryp:>>Like something loose in the bowl that occasionally vibrates over and clogs the jets.

That happens to me all the time even after cleaning a carb and flushing the tank and line several times.  Very frustrating. 

Remotely possible to be a plug but usually requires a wait time for the plug to cool.

Could be a needle adjustment or sticky needle seat but most likely what Shryp said.   I doubt it's compression related. 

On the 80 reading.  Compression readings are almost a black art.  For that old engine 80 is not so meaningful.  It could belch oil under load or perform very well with an 80. 

Don't know if those machines already had oil sensors but maybe an intermittent oil sensor issue cutting the ignition ??

Thanks for the replies, heres an update after I had a chance to look at things last night.

First off, when I opened up the stator, there was oil at the bottom.  not alot, but enough to put a film on all the parts.  Based on how hard the flywheel was to get off, i dont think anyone has been in there for a while, so hard to tell how bad the leak is. 

The condenser was if not original, very old.  the points looked ok, but needed to pickup some feeler gauges this morning to check the gap.  connections had a reasonable amount of corrosion, plus crud due to the oil leak.  found the kill line, which runs off of the throttle position.  wire sheath looked worn in areas.  so heres the plan:

     -clean all parts to remove oil.

     -replace condenser, and regap points

     -replace kill line with new wire

     -clean connections with emory cloth

A couple questions:

     -are the 3 tools shown in the manual (oil seal driver, protector and remover) required to replace the seal?

     -if I remove the stator will I need to retime the ignition?  reading through the process, this is something i'd like to avoid if possible

I'm feeling optimistic that fixing these things will improve how the engine runs (and like I said originally, it ran well up to this year).  If it doesn't do it, on to the carb....

I found a post on another forum where someone used a section of PVC or deep socket to install the seal, both of those seem like good substitutions for the factory tool.  Still need to know about timing -- if the stator comes off to replace the seal will i need to redo the timing?  Can I mark the position if it currently mounted and reinstall in the same spot, or will that not sufice?   thanks.

The flywheel/rotor/stator has a keyway right?  If so, when you put the flywheel back on, it should be set properly.  As long as you put the points back the way you found them, and have them properly set, you should be good to go.  Did you ensure the points follower was resting on the top of the cam lobe when you set the points?  If so, they should be OK.  Let us know how it goes.    

I think he's talking about the stator as in the holder for the points. 

I've had them off and would not rely on a pencil line.  Too much of a pain if you get it wrong.  To easy to get it right.  Well not exactly easy but easy enough.  You can set them with a multimeter.  At least for me that works best.   The procedure has been described many times in pior posts.  It's in the Tecumseh 3-11 L-head manual which is free online.  For the BTDC distance given in the explinations you can eyeball that or if the head is off measure directly using feeler gages.

trouts2 wrote:

Right -- maybe I described it wrong.  I've read the procedure in the manual, and the part of concern was finding BTDC and the use of the dial indicator.  Once you get that, your right, the rest doesn't seem bad.