Abby's Guide to Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more)
Username Password
Discussions Reviews More Guides
Abby’s Guide > Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) > Discussions > I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????

Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Search For:
edgenet


If you enjoy doing it, It's not work

Location: Toronto
Joined: Nov 27, 2010
Points: 84

I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Original Message   Dec 22, 2010 8:05 pm
I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????

If you are getting paid for what you are doing No matter how much you Enjoy it,   It's a Job
Replies: 28 - 37 of 47Next page of topicsPreviousNextNext page of topicsAllView as Outline
trouts2




Location: Marlboro MA
Joined: Dec 8, 2007
Points: 1328

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #28   Jan 2, 2011 11:58 am
Nice looking machine.  Just slipped in under the chute crank so no mods there.   You mentioned an issue with bolting it on.  What went on there?  Did you have to drill new holes or what?
edgenet


If you enjoy doing it, It's not work

Location: Toronto
Joined: Nov 27, 2010
Points: 84

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #29   Jan 2, 2011 4:52 pm
Yes I had to drill 4 new holes and the rear holes perfectly lined up with the transmission pulleys it was almost imposible to push the bolts from underneath. Bolting the engine down took me a few hours fiddling etc etc. If I had to build more of these all I would do is drill the holes push the bolts from the top just below the deck and weld the suckers and that would be a 10 minute job. This is why 1-of custom builds take much longer. All in all I am very happy with the result.
This message was modified Jan 2, 2011 by edgenet


If you are getting paid for what you are doing No matter how much you Enjoy it,   It's a Job
GtWtNorth


https://t.me/pump_upp

Location: https://t.me/pump_upp
Joined: Nov 16, 2008
Points: 264

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #30   Jan 2, 2011 5:21 pm
Congrats, you did a nice job. Hope you get some snow to try it out. But wait, don't you guys in Toronto just call in the army when you get any snow!

Cheers

https://t.me/pump_upp
edgenet


If you enjoy doing it, It's not work

Location: Toronto
Joined: Nov 27, 2010
Points: 84

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #31   Jan 5, 2011 5:02 am

Huston we have a problem. This has me a bit frustrated. The blower heats the belt to a point where it bakes it and due to the heat the belt shrinks and that is the end of the belt.  The thing that is frustrating is that this blower has an adjusting idler pulley allowing to make a fine adjustment on the belt.  The pulley I am using is ½ inch wide I am wondering if this pulley is to narrow vs an A&B wide pulley. Any suggestions

If you are getting paid for what you are doing No matter how much you Enjoy it,   It's a Job
MN_Runner


Location: St. Paul, Minnesota
Joined: Dec 5, 2010
Points: 622

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #32   Jan 5, 2011 7:38 pm
How's the alignment?  Are they perfectly aligned? Excessive heat is a result of friction (even small mis-aligment can produce large heat).  Do you have an IR camera?  If yes, you can see the heat source.
This message was modified Jan 5, 2011 by MN_Runner
edgenet


If you enjoy doing it, It's not work

Location: Toronto
Joined: Nov 27, 2010
Points: 84

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #33   Jan 5, 2011 8:24 pm
Mn-Runner you were correct the auger pulley was  out of allignment by 1/4" and I also re-installed the same size ideler pully as the orginal.  I installed a larger idler-pulley thinking it will be a heavier duty unit and for some reason that made the belt shake like crazy in the stop mode. I wish I did have the gun that would have help.

 One other point eventhough it has the ajustable idler pulley.  I am using  a 1/2" x 38" belt It is just loose enough to work with the 3" x 5/8' auger pulley. I changed  the pulley  to 1/2" x 3"  so I would be consistent with the lower auger pully  now  the 38" belt is to tight and the 39" belt is too loose even with the ideler pulley adjust to max-in.  I re-installed the 5/8 pulley with the 38" belt.  Buttom line if I want to use the 1/2" pulley I will have to find a 38-1/2"  belt. All off the off the shelf belts are sold  in 1" increments. At this point I am hopping the 5/8" pulley will provide a good grip using  the 1/2" belt. Nothing is straight forward. One step at a time I guess.   

If you are getting paid for what you are doing No matter how much you Enjoy it,   It's a Job
hirschallan


If it aint broke don't fix it !!


Location: Northern Hills of NY
Joined: Aug 25, 2005
Points: 327

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #34   Jan 5, 2011 10:11 pm
edgenet wrote:
 One other point eventhough it has the ajustable idler pulley.  I am using  a 1/2" x 38" belt It is just loose enough to work with the 3" x 5/8' auger pulley. I changed  the pulley  to 1/2" x 3"  so I would be consistent with the lower auger pully  now  the 38" belt is to tight and the 39" belt is too loose even with the ideler pulley adjust to max-in.  I re-installed the 5/8 pulley with the 38" belt.  Buttom line if I want to use the 1/2" pulley I will have to find a 38-1/2"  belt. All off the off the shelf belts are sold  in 1" increments. At this point I am hopping the 5/8" pulley will provide a good grip using  the 1/2" belt. Nothing is straight forward. One step at a time I guess.   



I seem to disagree. A "v" belt is supposed to ride on the sides of the belt and at the bottom of the "v" is supposed to be a gap, so when the belt starts to wear and get thin it can still have friction to drive the pulley where as if its riding on the bottom of the V it will start to slip and haet up. By using the 5/8" pulley the belt is sinking lower to the bottom and when that belt starts to strech a bit you will be losing grip and heating up.

 In a previous post you talk about A and B pulley combo pulley. A 1/2' belt is the same as a B belt but a combo pulley will have the wider belt ride on the outer edge and the narrower one lower to the center therefore when you use the combo pulley your belt ends up to long because,the diameter is smaller using less of the belt. You must look for a half inch increment belt or utilize the idler pulley. I can't see why you dont use the 39'' belt and utilize the larger idler pulley to take up the slack.

MN_Runner


Location: St. Paul, Minnesota
Joined: Dec 5, 2010
Points: 622

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #35   Jan 5, 2011 10:30 pm
Is the belt closer to the chute giving you the heating problem?  Just wondering if the edge of the belt is being heated due to a size mismatch. 
carlb


Joined: Nov 16, 2010
Points: 279

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #36   Jan 6, 2011 11:49 am
As previously stated, do not use a 5/8 pulley with a 1/2 belt.  It will just cause it to ride too deep and not work well.  I suspect it would burn up that belt pretty quickly
hirschallan


If it aint broke don't fix it !!


Location: Northern Hills of NY
Joined: Aug 25, 2005
Points: 327

Re: I have a Honda 13-hp GX390 engine I want to build a monster SnowBlower. What deck should I be looking for that can handle this engine??????
Reply #37   Jan 6, 2011 2:57 pm
carlb wrote:
As previously stated, do not use a 5/8 pulley with a 1/2 belt.  It will just cause it to ride too deep and not work well.  I suspect it would burn up that belt pretty quickly


+1

Replies: 28 - 37 of 47Next page of topicsPreviousNextNext page of topicsAllView as Outline
Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Guide   •   Discussions  Reviews  
AbbysGuide.com   About Us   Terms of Use   Privacy Policy   Contact Us
Copyright 1998-2024 AbbysGuide.com. All rights reserved.
Site by Take 42