Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I purchased and installed the Commercial Skid Shoes on the New Honda HS 928TAS tracked snowblower.   If you are considering this, here is what you should know.  YOU have to locate, center-punch and drill  4 -  1/8" pilot holes, then open them up with an 11/32" steel drill.  The bolts and lock-nuts Honda supplies are plain steel, as in they should rust together fairly quick on the bottom front of the machine.  If you hope to ever adjust them again, or remove them go to www.allensfasteners.com and order 8 mm X 20 SS Hex Bolts, lock washers, fender washers, and lock-nuts also made of SS.  Then you can trash the Honda quick rust serrated flange bolts, and nuts the Commercial Skid Shoes come with, Honda Gypped me on the washers they were supposed to have in the kit, you'll havta buy your own.  I chose 8 mm SS fender washers to secure the shoes in place.

When the light decision is made, I'll let you know how it goes.

Heh, this was a mod I had in mind.

On a OPE application, IMO, it does not matter what brand of film  cause we don't to a degree care about the toplayer (clearcoated or not) or how much or how little OrangePeel the film has.
Just go with the thickest film FOR the application you want but on curved areas, you may want to go with a thinner film.

Do it. The clear film will look like crap BUT at least you never have to repaint/touch up .

FWIW, I have clearbra on varying degrees on all my cars. The biggest difference that you will notice on protection is the the clear bra that goes underneath the rockers....
Personally, I prefer Ventureshield out of all the films out there.

newYorker -

re: my other thread response on instructions, a picture speaks a thousands words. No need to mail the instructions.
Just post a pic of you latest mod and it should be all clear to me...

I was only curious on placement.
If one was to not use the stock nut location, which appears to be centered on the bucket, where else are you making the new holes.

The holes are 1.5 inches above the welded nuts, in the depression that looks like a partial circle.

Use neolube on stainless bolts and nuts to prevent galling of threads. Find neolube through google search.  Suggest flange nuts when available.  They had them at the site you recommended but I didn't see the ss fender washers.  My new HS928 has the commercial skids but not sure if bolts are stainless steel so I'm going to change them.

I waxed the metal parts of the snowblower to prep it for use.  Was told to wash it with hot water after each use and to spray it with WD-40 to prevent rust.  Oh, and store it in a garage; not outdoors.  A buddy uses NU Car finish on his snowblower.  Likes the hardness of the finish says it resists the effects of snow hitting the surfaces in the chute and auger housing.  Never used it so I can't comment.

So far (Dec. 22, 2010) and no snow in Pittsburgh. 

Do you notice an improvement in the ease of moving the track drive blower around with the new skids?

Any easier on the back (or harder?)?

Jeez....me wonders what the purpose/intent of of the welded nuts would be for then....

I would think or want that area to be a Ridgid as possible with less holes or have a better suspect area for rust.

Thx for the clarifiication AA....

Underdog wrote:  
It was a bit more effort to turn, especially those 180 degrees.  The bucket was more stable and less wandering since I have a 32" wide bucket.

Hey New Yorker :

How are those MODS/tweaks coming along.
Post some pics when you get a chance.

I think modding snowblowers in the winters is as close to modding cars I can get during the warmer months ;-)

BTW, any concern with the semi heavy bucket and the 8MM SS bolt....
I'd be inclinced to use supplied hardware. As long as you are properly keeping the chassis waxed, lubed & or weatherproofing treatment, it should be fine to a degree.
And, it will be stronger than the SS bolts...

New Yorker- I seem to remember you live on Long Island. Stop at Graingers and pick up a jar of Marine Grade Anti Seize by Loc-Tite . I've been using it for years on blowers,mowers ,cars,motorcycles,outboards,fishing reels etc. The stuff can't be beat for insuring disassembly of threaded connectors. 

Marc 

The Commercial Skid Shoes seem to be the better way to support the auger casing.  The uneven ground would cause te ends to scrape if I were to have used the rear mounted skid shoes.  On a smooth level surface they might be fine, but not on uneven gravel, and a slope which describes my driveway.  No need to use anything on stainless steel bolts and lock nuts once they are installed, they always work great.  I have a heavily plowed, heavily salted road that makes the snowblower vulnerable to the corrosive salt, hence my obsession with SS fasteners especially where the machine scrapes along the ground.  When I get the Mods finished i'll take a few pictures.