Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

.......

i have search google and i have found nothing :( please anyone?

thanks

The weekend probably has a lot folks busy with various chores. I'm sure someone will be able to help you in the next couple of days or so. Wish I could help, but I've never even heard of Jari Jaw Snowblower.

sclark wrote:

Was that the Star Wars model? Oh wait that was Jar jar Binks. :D

Try searching here. Last year a woman who is involved with the company that is a descendant of Jari posted here, and a year or two before the son of the original owner was here also. There may be some info there. I had never even heard of these but found out about it from those threads.

.....

http://s366.photobucket.com/albums/oo109/juskim_photos/Jari%20Photos/

linked from:
http://www.abbysguide.com/ope/discussions/20781-A-1.html

   What is the issue with the pulley system? 

.......

What is your model?

If a tensioner is being held tight with wire then it probalby should have a spring.  Many makers have drive plate that always turns at speed and a friction disk that brought up to meet it after a clutch lever press.  The wheel drive belt is always tight and held tight by a tensioner pulley usualy under spring tension.  If similar, look at the tensioner and for a hole or small bar that could catch a spring.  Then look 2-4 inches away for a hole, slot or edge over which a spring could be put.  Get a spring at a local hardware store to keep the tension reasonable.  Other than that, take a pictures and post them.  To post a picture put it somewhere on the net.  When posting, the post header has a letter shape.  Click that and insert the link to where your picture is.  The posting software will get the picture and insert it into the post.

.......

....

.........

   The tensioner on the left is probably for auger engagement.  How does that arm move?  Does it just swing on the pin/bolt below or is it engaged by something out of view?    There are 3 holes in that arm that could be for spring connections.  

 

What is that arm in the center with the spring?   I assume that goes back to the operator.  Is there any writing by the operator to indicate what it does?

 

The tensioner to the right looks like the drive tensioner.  There’s no pulley for it?   Is there any driven pulleys attached to the bucket?  Where is the stuff that the belt turns?   That arm on that tensioner also has holes so a place for a spring.  It looks like its got part of a spring poking through on the bottom hole.  If there a spring behing it?

 

A little more info would be helpful.   Sometimes I explain things and in the process of verbalizing them understand more.  Putting vague understandings into concrete words and sentences that have to make sense forces more understanding.  Maybe you could write up what you know about the internals.

 

Could the center arm have two springs for tensioning one or the other arm for forward and reverse?   That would probably require two pulleys below.  Are there two pulleys for drive out of view.  I doubt if the two belts are for forward and reverse but it could be true.  Cannot see all the components so tought to say.   What's attached to the bucket?

 

Where are the auger drivem components if both of those belts are for drive F/R?   The bar left to right in there seems to be the wheel axle.  What does the chain drive and what does the big gear to the right drive or are they both driven by something out of the picture?  What’s out of the picture that the belts drive?  Again if both of those belts are for F/R then your missing auger components.

 

Rather than both belts being for F/R could one be an auger drive and the other wheel drive.  Do you have drive and auger clutches on the handlebars?  Probably not but is there something you flip to get wheel drive and something else you flip for auger drive?  What operator controls do you have and where do they run?   Some machines have drive belts that are always tensioned so part of the drive mechanism is always active and always turning when the engine runs.  You flip or move something to bring parts up to meet what is driven to  get drive.  For the auger you usually push or flip a lever to bring the tensioner into the belt.

.........

Did you ever get a reply to your questions. Someone gave me an old Jari that runs but I can't figure out the belt system and how things get engged. any help would be appreciated.