Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I recently picked up a Airens ST1032 snowblower. It is in good shape but, when I bought it it was taken apart. The previous owner said it did not have any spark. I replaced the points and condenser and I also removed the cylinder head cover to check the condition of the piston and valves. They look good but i did notice a hair line crack in the cylinder head. (the part the spark plug screws into). It does not appear to go all the way through.

I am in the process of putting the motor back together, but with the cylinder cracked, I am also considering getting a new motor all together. How do i know if the head is trashed? It does seem to have a decent amount of compression, but it hard to tell, because i dont know what "normal" is for that motor?

It is a 10hp tecumseh HM100 motor

Any advice?

Trouts is probably on the right track.  I agree that it's probably a float setting issue.  I had a little two horse Evinrude engine that I couldn't get to run right for the longest time.  I was too lazy to pull the engine cowling off to take the carb out and tried to adjust the float with the carb on the engine.  Not a chance.  I had to take the engine apart and pull the carb to get the float setting right.  As he says, they can be very finicky.

The float and float needle work on the  principle of leverage.  When the float goes to the bottom of the bowl, causing demand for fuel, the float needle either opens on it's own with gravity or is pulled open via the float lever and a very small wire clip attached to the float needle and float lever.  The adjustment of the float is very critical and often only hav a millimeter or two float movement allowance.  If you have a fuel starvation issue, that means the float cannot move low enough and is not allowing sufficient movement of the float needle to permit sufficient fuel flow.  

I've had occasion when I couldn't dial in the float in and had to get creative.  So I carefully put the carb in a vice and rigged up a small bottle of water to the fuel hose going into the fuel inlet.  I then allowed water to flow down to the carb and controlled the float by hand to watch how much movement it needed to stop/allow the water flow.  This method is OK to get it close but water is heavier than gasoline and fine tuning might be necessary.  Focus on the float setting.  Sooner or later, you'll get it right.

    Never used a plastic float.  I don’t know if they ride different or are set the same way.  You can ballpark it by setting similar to the brass float then subtracting a hair from the tang to open slightly early.

 

>>The carb linkages do open the throttle part way when the lever is at "fast" I was under

>>the impression that this was normal, and the govenor would open the throttle more

>>when needed. Is that correct?

   Yes, the linkage throttle movement is a gross movement so it’s probably fine.  The governor is generally active at slowing down the motor (pushed internally by flyweights) or passivly being pulled back by throttle springs.

 

>>I did install a inline fuel filter, could that be causing problems? but, then again, the carb from the st824 works fine with it.....

 

   Also, draining fuel out of the nut will double check that  Remember, you just cleaned your carb and having problems which act like the carb is dirty.  You might want to check things again because it looks like some area you cleaned or set right is now dirty or set incorrectly.  It won’t need another dip but poking the passageways and verifying the float will probably cure it.

   Every time you put the gas line back on you are pushing hard on an old line that can easily break off crud immediatly or loosen the wall  which will fall off later.  Chances are the line did not come off easily and you had to use pliers or wedge a screw drive behind the line to get it off.  That puts a lot of stress on an old line. 

   

I think the emulsifier jet/ nozzle is slightly plugged and needs to be cleaned...

-Friiy

I give up. I adjusted the float several times with no difference in the way it runs. I ordered a new carb today.

dvdkea wrote:
See if Trouts wants your old carb  to find out if he can analyze the problem.  He might be able to press it into service on a machine he's repairing. 

I hate giving in to a misbehaving carb!

I hope you looked on Ebay before ordering in the new carb.  Big savings to be had there on stuff like that.

I may just throw it up on ebay to get rid of it. I'm sure it can be fixed, but i just dont have the patients anymore. They new ones are available on ebay for about $10 less than i can buy locally. I'll buy local.

I have learned a lot about the st1032 already. Seems like it will be a good machine. I live in upstate NY and we had a very mild winter, but I'm sure we will get a lot of snow one of therse years...

Any idea what a machine of that size\quality would go for today?

   It does get a bit messy and frustrating to keep making adjustments with no result.  You may want to keep your carb around for another crack at it later.  The new carb will not have an idle or main jet unless you snagged an old NOS carb. 

I was able to get a NOS carb locally that does have all of the adjustments like the original one does.

I am assuming these are better than the non adjustable ones?