Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

We got a mess of this wet slushy stuff some were calling snow yesterday. Snow just can not be any heavier than this stuff. I knew it was gonna' Make the blower work hard. I have a 2005 Ariens 926 pro. There was maybe 5" of the stuff.  It was the biggest challenge the blower has seen and while it barked at me more than ever it was impressive to see and hear. The unit threw the stuff a minimum of 10 ' . This was for the pure slop. I thought for sure thr chute would clog on this, even though it has never has before.  There were moments that it filled up  but then but then "fudged?" out somehow. Never really missing a beat. Maybe stumbled but not missing. For the max throwing distance it didnt seem a whole lot shorter than  normal . It varried as the snow changed throughout the drive. The neighbours blower was benched and he resorted to the trusty shovel. I did his 2 contract jobs a few doors down and a couple more drives as well. All in all the blower earned its spot in the garage ( like it hadn't before? ).

STILL AN ISSUE is that irratating slipping fricktion slip drive. Never liked it never will. Damnit, when I say go, GO!!  Now it only happened a few times and recovers within seconds but it pissed me off every time. I've sealed the unit up to prevent water/snow intrusion but I'm goin' back in. They've peppered this drive housing with so many openings forcing its fate.  To me it is unacceptable behaviour and I want to beat it into submission. Can you tell I hate it?

I'll lighten up a bit and praise the differential. What a work of art it is and a pleasure to turn. Effortless one handed turns and goes where I piont it. I have a trigger to lock both wheels when needed like the super heavy EOD yesterday. It did not unlock immedeatly upon release but that is a minor adjustment I'll tend to shortly.

The motor, a 9.25hp some say is the same as their 11ish hp.  Now I have no idea if it is or not but I can say without reservation that this 9hp is plenty.  Who can't love more hp but I'm guessing that there can't be much difference. My driveway layout is such that I have to send that snow a long way and this unit does it.

All in all I am very impessed and can you beleive even with the fricktion slip "drive" I would do it again?

On a side note there were some single stage units around town that were doing an impressive job in the giant slurpee.

Tomorrow gonna' heat the garage  and give the beauty a mid-winter wax.

Paul7: I've heard people bark about the 7hp Ariens machines but still it should be potent.  It almost sounds like my 3's and 4's could match yours.  They'll toss very wet slush 5-15 feet but there is a big difference between forward or to the side.

Borat: What's with the Yo?? Usually that form of address is  to be an insult. 

The 3300 comes from the factory.  I called the other day to find out about newer models auger and impeller speeds.  I asked about the 3300 RPM  which was a surprise.  The rep said refereing to the new Briggs engines that they "all" ran at 3300.  I had asked him to qualify that also and he did.  Now he may be talking generally meaning most and not every single model but as told to me by the rep the new Briggs engines as a group ran at 3300.  If yours is stock at 3600 then it could be just a variant engine or you may be running over REV'ed.   What does your manual say you should be running at?  Possibly Toro recommended speed is 3300 versus max for the block but then you're probably running SeaFrom and experiencing much better performance and higher revs.

Borat: If you re-read the above posts the reference is to Toro Briggs engines.  They run at 3300 as told to me by the Toro factory and just checking their service manuals are goverened at 3300.  You have a Simplicity yes?  Your either running over reved or Simplicity has configured their engines at 3600.

Trouts, maybe if you ran some Seafoam through your engines more often, you'd see 3600 rpm... (joke)

Mr. Trouts: Borat: What's with the Yo?? Usually that form of address is to be an insult. On the contrary. Yo is no more of an insult that saying Hey Trouts. In what part of the country is using the term yo, an insult? I'm interested to know. Regarding your comments concerning engine rpm. Why not put a tach on those engines just to confirm their rpms. You are correct about the Simplicity and B&S engine being governed to run at 3600. I might be wrong but just about all of my four stroke OPE engines (pressure washer Mitsubishi, Champion generator, B&S roto-tiller) also run at 3600 rpm.

My 305cc operates at a fixed 3600 RPM as well according to electronic tach. I notice in my engine owners manual the following statement: "Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM" http://www.briggsandstratton.com/pdf/owners_manual/100%5C277104TRI_B-Domestic.pdf

JohnnyBoyUpNorth wrote:

ZING!!!!!!!! Ouch.....

Borat: Why not put a tach on those engines just to confirm their rpms.

 

?? Why would I want to do that?  If the reading was other than 3300 it would be non-factory so what is the point?

 

Borat: about all of my four stroke OPE engines (pressure washer Mitsubishi, Champion generator, B&S roto-tiller) also run at 3600 rpm.

Again what is the point?  Lots of Briggs OPE stuff runs at non-3600 settings.  Your stuff may run at 3600 so how does that relate to the discussion of Toro running at 3300?

trouts2 wrote:

To the Sir, Honourable, Your Highness, Emperor of the Universe Trouts: Sounds like you might be skeert to find out!