Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

Will this work? Can I replace a broken foam float in this kawasaki 4-cycle with a plastic float.
The motor is model FG300D Code:FG300DHS00 Number: FG300D1351
I have not been able to find a replacement foam float for this mikuni carb. Shown below is the broken foam float (it was my fault, I got careless)
and a replacement float that appears to be made of plastic.

Yeah ,   Foam is still used..   foam will not crack and take on gas and sink...  

Friiy...

What are you working on that has aTwin Kawasaki engine?

The one on Ebay is what?   $10 +shipping  ..... to order the right one is $24.00  + shipping....

      I could fool around with it for 4 hours and make it work  by glueing it with special glue,  I could cross my fingers that the plastic one fits,  or  I could order the right one for $24 + shipping plus the gasket around the bowl it needs ...   I think it comes down to time management..  We  are worth more than $14  we save for the 4 hours we screwed with something.  

When I was young I had lots of time and no money- Now I am older I have lots of money and no time...   :(

Friiy

Alright I bite.....

How far will this thing throw leaves with a Kawasaki  on it?

Friiy

friiy wrote: Thanks for this. I will follow up. I'm curious to to know if the part the send will be the foam or plastic.

<BR> friiy wrote: <BR>I have no idea. From the looks of the rest of things, Ransome seems to be ok. I don't think they are still around though. <BR>I don't see their name anywhere locally. I think the company may have originally been from the UK? I seem to recall a Ransome mower that was used to mow the greens on a golf course. I'm sure that by the time (if?) it runs again, the leaves will be history.
I'm following the tricks I learned here to clean up the carb.

If I'm looking at $24.00+ just for the float, I'd be looking a replacing the whole carb. Chances are that there is a carb out there that will fit and be reasonably priced.

I show the whole carb runs about $109 to $124 bucks.....





Friiy

I found a place about 30 minutes away that has a float in stock for $33.46 with tax. (Most of the outdoor power equipment dealers in my area have abandoned Kawasaki for some reason but John Deer dealers carry the parts with a different part number system).  If I buy it in person at least I'll have the chance to hold the two floats up next to each other and compare.  If I knew that everything else on the engine was in working order I would not hesitate to snatch that float up. And  I  see the point about not wasting my time just to save and extra $10 to $15 not to mention all the frustration that comes with getting the wrong part.  At the same time I'd like to learn from past mistakes and not go crazy.  I'm working on getting the rest of the carb cleaned out. I  was thinking of patching the float together just long enough to get the engine running to diagnose other potential issues.  What if this engine is standing on death's door and something is really really bad.  Without knowing the history of the Ransome I'm at a real disadvantage.  I could take thin needle and pluck the float together like a voodoo doll.

If you plan to glue the float back together, I recommend using JB Weld. That stuff is miraculous. It doesn't seem to be bothered by gasoline and oil. I've used it on a lot of different applications and the stuff hangs right in there. There are two types of JB Weld. Regular and JB Quick. Not sure if effectiveness is compromised using the Quick. I use both and haven't had a problem with either. You might want to do a test piece and allow it to set up then put it in some fuel to see how it reacts. Personally, I think it will be fine.