Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I did a search and found a few references to this machine but no answers.  Any one have one of these?  15.5 snow max engine, heated hand grips, 30" wide.  I can't find a listing for auger diameter or impeller diameter.  I called John Deere and the guy that was suppose to be the snow thrower expert didn't know either. 

What is the Easy Steer drive system?  The literature says: 

Easy Steer® drive system giving continuous power to both wheels and auto speed adjustment

Is it similar to the Ariens auto differential? 

I've heard that the units are built by B&S which translates to Simplicity.  They do have cast iron gear cases like the Simplicity.  The chute control is different than the simplicity and so is the turning method so they are not exactly the same.  I'm trying to compare the Simplicity L1530E to the JD 1130SE.  Any help would be appreciated.

Rick

Royce,

   Could you go into more detail about the hydro?  You seem to be a sharp guy and know a lot about them versus friction disks.

   No need to make one, although that is a good idea.  Husqvarna has a hydrostatic model and the  Husqvarna built, Craftsman models 52993 and 52070 are also hydrostatic,  No more friction disc problems!! 

Swoods wrote:
I purchased 2 of those  those little blinking red lights that truckers use when they have to to make an emergency stop  on the side of the road They are  LED , use 2 AAA batteries and seem to last forever. I got them at Walmart, I think they were $5 each,   mounted them on the side of the cab.

trouts2 wrote:

I have used hydrostatic transmissions on many types of equipment over the years, and have been very satisfied with them.   When  I saw the Craftsman 52993 ,14.5  305 Briggs.  I had to have it.  Built by Husqvarna, who also makes hydrostatic models under their own  Husqvarna name,  I researched the hydrostatic transaxle and found out that they were built by Hydro Gear.in the USA.  , a very large manufaxrurer of hydrostatic transmissions and transaxles.    The ones in the snowblowers are the WB (walk behind)  series, very similar to the ones used      in tractors.   They still have the traction belt setup but it drives the pulley on the the hydrostatic transmission . So to operate, you hold down the left control lever (like you would in any snowblower) this sends  the power to the transaxle.  While holding down the left control lever ,(acting like a dead man control)  the drive speed control lever  is then all you have to use, forward to move ahead , nuetral in the middle and moving the lever back for reverse (just like in the treactors )   Before doing this, you have already set you engine speed to max, as you would do in any snow blower .  You can shift the lever from forward  to reverse at any time.   The further you move the lever forward , the faster you go,  Same as moving the lever back for reverse---   So,  It is variable speed.  You can move forward at a speed that is much slower than the friction disc is capable.  You machine doesn't have to work nearly a hard at any speed or load. There is over a 20 to 1 multiply in torque,  

Has anyone had a chance to use their 1130 yet this year? Does an engine has to have a pressurized oil system to have an oil filter? I was seeing if it is possible to add one, but maybe it's a sling oil system where it won't work.

you can not put an oil filter on an engine that does not have an oil pump, it wont work.

I purchased the JD 1130E from Lowes in 2009. The "easy steer" system is probably fine for paved driveways but I live in the country and have a very large gravel driveway. Because of the uneven surface I think the easy steer system is a detriment to me. Is there any way to disenage or disable it? I find myself wrestling with the machine to get both wheels turning in sync. Thanks.

Pull the bottom cover off to see why it's not engaging/disengaging.  If it's the same set up as my Simplicity, it could be a problem of too much of the wrong grease on it.  If the grease isn't suitable for winter conditions, it might create too much resistance in cold temperatures thus not allowing the engagement couplers to move freely. 

SteveJF wrote:

Hi there...your machine's "easy steer"  feature is an Auto-Lok differential from a company called Hilliard...they supply the industry with this differential unit...It is neat system when it is properly integrated into a product so it is effective an efficient...The problem that your having is that your Auto-Lok differential is mounted on a main sprocket and driven with a chain....same concept as a bike...The problem is that there is too much slack and not very much surface contact for the driving mechanisms to work properly. Ex: Ariens is using this technology on their Platinum and Professional series machine too...however, it is integrated and designed differently and better in my opinion. Here is the reason why...The main difference is that the ARIENS is using a spur gear around the Auto-Lok unit and a pinion to drive the gear for both wheels. The spur gear surface is about 1" wide and the pinion even more. Perhaps, 1.250" of surface for the pinion. I would have to open and measure to get exact size, but its about that. This surface contact increases the stability, rigidity and decreaes the vibration of the axle. John Deere doesn't have a spur gear around the Hillard Auto-Lok unit and neither a pinion. They are using a sprocket and chain to drive the axle. The sprocket is fitted to Auto-Lok and expected to give you that Easy Steer you looking for. Unfortunately, it's not giving you the performance you were expecting....Perhaps, it is also defective too...eventhough it is mounted on a sprocket and chain it should still be going on a straight line and in-sync...

Here is a link to JD manual for your machine on page 6   https://groundscare.custhelp.com/ci/fattach/get/32489/

Here is a link to Ariens service manual..go to page 20 figure 18 to see how Ariens is mounted differently.  http://apache.ariens.com/manuals/02983600.pdf

If it is a real irritant for you...you might want to consider removing this Auto-Lok and installing a straight sproket...just remember if you this, it will be harder to turn. This is how standard MTD snowblowers operate...

Can someone please test the voltage on the headlight connector while at full idle? I keep blowing headlights. The voltage changes when I turn the heated grips high/low/off. Voltage when the handgrips are off: 16.4, Voltage when the handgrips are on high: 12.5 Voltage, when the handgrips are on low: 13.4