Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I bought this machine because I needed a rugged machine that would last me. I would rather purchase a "Tim Taylor" machine rather than fuss with an inferior one. This beast has 13hp, 36" wide, locking diff, heated hand grips, light, elec start, ect.... I have a 100 foot paved driveway. It has snowed 4 times since I purchased it, and it has broke down on me 3 times.  everything from a factory recall that i wasnt notified of, so it burned belts (4)!!, to nuts & bolts falling out, chute breaking, auger stops turning, wheels stop driving, etc.... The dealer has a special place for it in his shop that they dont fill when it is at my place. I believe this machine would last forever,  if i dont use it. The dealer stood behind me 100% when I told them enough is enough I wanted something done, money back, or a replacement. Now it has snowed today, 20", I have a bad back and have to shovel while the ariens company sits on my $3000.00. Anybody else have this problem?

That story made my day....a good laugh...Great visuals.............THANKS!
Packo

Possible causes, least likely to most:

1. Next time you remove the pulley cover measure the auger system pulley maybe its too small and the impeller RPM is too low;
2. Make sure you put the choke in the "off" ( a.k.a. open or run) position;
   
3. If you go too slow there isn't enough load on the engine the governor won't cause the engine to rev up, you can hear the difference when it happens, try a higher speed setting;
   
4. The belt is too loose and slips whenever the auger/impeller is under load.

nhmatt wrote:

I think you may have bought the wrong machine for your needs.


nhmatt wrote:

You misunderstand the operation of the differential.  The idea is to have power going to both wheels, whether or
not you're turning.   Just like on a car this works very well as long as both wheels have traction.  But the way the
differential works is that it will end up sending all the power to the wheel which loses traction (like on ice).   If
you don't want this to happen you have to manually lock the wheels (the new limited slip differential will do this
for you).


nhmatt wrote:

I don't see how the snow could exit the chute if it was in the center of the machine.  The snow comes
off the impeller tangent  to the rotation of its blades and if you want the direction to be "up", so you can
then send it somewhere useful, the chute will have to be on one side of the impeller.


nhmatt wrote:
This is why I think you picked the wrong model for your needs.  In my mind a 36" wide machine is for quickly clearing
a large area of snow that is not too thick.   For deep snow you want a narrow machine.  Especially for something like the
snowbank left by the city plow.  The first cut into this has to be the full width of the machine and 36" is asking too much.

Paul

I absolutely bought the wrong machine.   But I don't undestand your point that a 13hp machine with a 36" bucket shouldn't be able to spit 6" of snow in the lowest gear possible.   This is the first time I've had someone suggest I should have a smaller machine, because I'm asking too much work from the biggest, baddest, snowblower ariens could make.    I believe my point WAS that this machine couldn't do the job I was asking of it, which is anthing more than 6" of powder.  Go figure, a snowblower that's affraid to get wet.

 If you look at the honda the chute is directly at the top of the impeller, making the throwing distance the same to either side.  Also, they don't put the battery directly in the path of the snow coming out of the chute (not that you should waste your money on electric start with a honda).  Maybe that's the reason in 10 years it only clogged when I sucked up a blue tarp.

I will be the first to admit I bought the wrong machine.  Its great to turn as you head back to the garage to gas up (gas hog) or to tighten the belt, or to let the auger/impeller thaw out because it doesn't like to get wet.  Honestly, buy a cheap, cheap cheap machine instead of wasting your money on an expensive one that was built cheaply.

I have a Honda at work and at home and both have the chute off center.

Ok Ok.  I understand what you mean with the need for release of snow at the tangent to the circle, and how its going to be off-center no matter what if you want to get all you can from the centrifugal force of the impeller.  Just like throwing a discus.  But take a good look inside both chutes, working and not,  and you'll notice how much more the snow bounces around in the ariens, and how the chute/auger in the honda spins the snow out.  Maybe its the size/speed of the impellers, where a faster impeller would mean it could be smaller and therefore less of a difference from right to left or whatever you want. 

Honda throws the snow farther, and its not just the power of the motor.   I've had a lot of xtra time to think about it while I'm working on this machine, instead of actually using this machine.  Other ariens may be fine, but this one model is a dud.

The Honda has a much smaller space between the impeller and the housing. This is why it throws like it does. If you install a Clarence impeller kit o n the Ariens it will become a new beast. I know because I did it on my 1128dle.
http://smllengns.tripod.com/

The clearance between the impeller vanes and housing on my  Simplicity looks to be around 1/16th of an inch.  It throws snow better than anything I've used before.  I agree that closer vane/housing tolerance will eject snow further and at a faster rate.

I couldn't agree more that the 1336 Pro is an expensive piece of junk. I am looking foward to all the breakdowns described because i've been lucky there so far but I've got a 2 year old machine. My complaint is that it could not cut through 4" of powdered snow without clogging.  After an hour or so of this recently I had had it and sent it into a snow bank and got my shovel. After a half hour of shoveling, I broke the shovel over the 1336. Poor shovel!  I've tried silicone, WD40, belts, Etc.  I hear Honda is the one. Ariens chute design is a LOSER!!

fpjungle wrote:

Don't rule out Simplicity/Snapper.  They're top notch.