Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

I have an Ariens 9526DLE that I bought Fall 2007.  It works well and throws snow out the chute like nothing I've seen before.  However, the auger seems to spit/leak out snow on the righthand side (respective to when I'm looking at the auger housing directly from the front).  I took it to the dealer and they said I had a 1/2 sheared shearpin and replaced it under warranty.  That didn't fix it and I'm still left with snow leaking out that side.  It's annoying as it leaves a small trail of snow all over the place that I have to shovel up by hand.  I would characterize it as snow being thrown/spit out forward as the auger spins.  It happens when I'm chewing through snow greater than 2" high.  I thought the auger rail on the right side was installed backwards perhaps... can someone take a look at the pics and confirm the auger rail is installed properly?  Thanks!

Mine does the same thing. I'll have to check today to see how much comes out to the side. It seems to be thrown mainly forward and is then picked up.

there is a thread here on the same topic but i can't find it now. it has something to do with the snow hitting the auger and the auger turning 130 rpm per minute.it said to check and make sure the edge of the auger is not bent away from the auger housing. i would check the right and left side auger clearances/ to housing and look and see if right side is identical to the left side.   found the thread! there are more responses following this post.search "926dle loosing snow" in the upper right search for box then click ajace link! hope this helps!!  now i'm off to tampa for the week!

AJace I have an Ariens 926 Pro because I like Orange Location: Near Gettysburg Joined: Points: 969

Ariens 926 DLE loosing snow Original Message   Jan 24, 2005 1:11 am Quote I did try my 926 DLE "Orange Crunch" this weekend.  I noticied that snow was coming out of the auger housing on the very left in a circular pattern like the auger moves.  I stopped the auger and a little snow came out where the deflector meets the chute.  About a 1/4" gap there.  Is any other Ariens 926 user experiencing this?  Ariens 926 DLE Professional; Toro S200; Craftsman LT1000, Echo ES-230;

I used the snowblower this AM to clear an additional 4" we got yesterday. The snow was light as it was in the previous 9" snowfall. The auger on the right side is throwing a small amount of snow forward, but not to the side, so in my particular case, I don't think there is a problem.

I will explain the root cause of the problem. If anyone finds a solution, please post it.

The impeller acts as an air fan.

In theory, the air is inputted from the front of the blower housing and is completely outputted in the discharge chute (i.e. the air flow is from the front of the blower towards the chute).

In practice, the impeller produces too much airflow to be completely outputted in the chute. What is actually happening, is that the air is inputted from one side of the housing and the air is exhausted at BOTH the chute and the other side of the housing.

This can be confirming by moving a light rag (or a candle) in front of the housing to watch the air flow.

So when the snow is being blown, the fluffy stuff is ejected on one side of the housing according to the airflow.

Does that unit only have three impeller vanes?   Is that something new? 

Here's a pic of the four vane impeller on the Simplicity:

My Ariens has 4 impeller vanes. I think all the current models have 3.

Looking at the backing plate for the impellers, it's clear that the Ariens used considerably less material and one vane less as well.  Saving money on steel I guess?   Understandable.  The Chinese were sucking up steel in 2007 and 2008 at a phenomenal rate.  Steel prices (as well as many other metals) went through the roof.  Personally, I'd rather pay more for the product than have it built more cheaply.  A name is only as good as it's product.  When the product no longer deserves the name, consumers will catch on and the name will lose it's marketing value.   I hope all of the domestic manufacturers don't follow this example.       

  I can't speak to why they made the change, but I'd just like to point out that it could have been seen as an improvement because fewer blades means it's easier for the snow to get into the impeller in the first place.  Reducing the number of blades but increasing RPM a bit would allow for better snow ejection.

I.M.Mike

For some reason, that doesn't sound right to me.  If fewer blades are more efficient, why not go to two blades, or better yet, one?   Funny how that works on a snow thrower. 

If you look at an airplane prop.  more blades = more efficiency.   I know it's a different application of blades but one would think that the fan effect of more blades would move more air and thus more snow.   I would suspect that the theory of fewer blades is to allow for greater openings between vanes and supposedly larger volumes of snow to enter into the impeller housing.  That poses another problem for me.  Considering the rotational speed of the impeller, one vane less wouldn't seem to offer a lot of opportunity for more snow to get in.   Someone will have to clue me in on how fewer blades is more efficient... 

For what it's worth the impeller in my 1999 Ariens 1024 has six blades, 1/8" thick steel.

automatic1stdown, is the impeller shaft bear metal ?  Looks like it's rusted (Ariens
used to paint it).  If you haven't already done so you might want to take out the shear
bolts and inject grease while turning the augers until the grease comes out the ends

Paul P