Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

My Yamaha snowblower will vibrate a little at low throttle.   Its not an issue for me but the choke arm on the carburetor vibrates and rattles all around. I'd like to remedy this. I picked up a metal punch (really small) some JB weld a scotchbright pad , some contact cleaner,  and now I'm ready to go.  What is my next step?

An R5?  Alright!  I have a '72 Mandarin Orange R5 out in the shed waiting it's turn for restoration.  Wild little hotrods those old things were.  I restored/hopped up an RD400 earlier this hear.  Lots of go fast goodies in it and virtually every possible wear item replaced.  I had a bit of a learning curve getting it tuned correctly with the modified air intake system, modified carbs and expansion chambers as well as setting the the best programable electronic igniton curve.  Once I had everything dialed in, I was startled how quick this little thing is.   Tuning session require testing sessions.  After the last adjustments, I took it out to a lonely stretch of highway and stopped.  I launched the bike and from second gear up, I rung the engine out to 9500 rpm each time before shifting.   I swear that in less than 15 seconds it was doing 100 mph.  I was still in fourth gear!   That was enough for me.  I cut the throttle and thought about what I'd just done and said to myself, "Getting caught at these speeds, I'll be going to jail."   I didn't quite expect that kind of speed from an old  1976, 400cc bike.  Here's a pic of the 400 & engine:

friiy wrote: OK, I have searched the net for Kawasaki TD-24 and TF-22 engines.  I'm coming up empty.  Can someone throw me a bone.  What ope did these run on?

borat wrote:
I loved the sound of my bike once I put those expansion chambers on.  I moved the footpegs back,
had clip-on handlebars, single seat.  At the time I was the only one on the road with a racing fairing,
now they've all got them.  The people in the shop where I worked thought I was weird.  We sold
Honda and Ski-doo/Canam, so I was a bit of a traitor.

Programmable ignition curve ?  Never heard of such a thing.  I remember playing with jets and
needles and then setting the timing so it wouldn't knock, that was about it. 

I went to the motorcycle mechanics school in Daytona Beach back in '77.  That was a blast.  One
of the teachers was into hot-rodding 50cc mopeds.  He had one that would do 70mph.

Paul

I replaced the points/condenser/coil with a state of the art MZ-B/Zeeltronic electronic charging & ignition system.  The Zeeltronic CDI is programmable.  It comes with a hand held programmer that plugs into the CDI.  I can program the advance of the ignition curve with up to ten stages of advance.  For instance, low rpm requires more advance to develop torque so I'll set the programmer at 24.5 degrees of advance at 1500 rpm, 23 degrees at 3000,  21 degrees at 4500,  19 degrees at 5000 etc... down to 16.5 degrees at 9000 rpm.  The real benefit of programmable ignition is that the heat developed by the engine can be transferred from the cylinders/heads into the pipes.   That contribute to two positive results.  It reduces heat in the engine and increases heat in the pipe.  Both of those factors are very important for reducing engine wear and increasing power.  Reducing engine heat is pretty much a known factor to prolong engine life.   Increasing the temperature of the gases flowing through the pipes increases gas velocity which in turn assist the engine to breath better thus make more power.  From my experience, it works.  Power is very strong for an old 400cc engine and after a long hard highway run, I can put my hand on the engine heads without burning my fingers.   New tricks for an old dog.  

  

 

The Kawasaki engines I was talking about were on a lot of diffrent equip.   Astron, Kazz, TMC, even the old Homelite commerical trimmers..

I found one picture of a TF22 engine on a Hedge trimmer,  I don't know what brand... Alot of people at the time thought that Kawasaki made the equipment..  but they were just a supplier of engines..

 

This you could get this engine for a few diffrent applications,  They sold it with a fuel tank fill pointing the cap whatever you needed it depending on the mount...this engine was about $280 bucks by its self...  The hedge trimmer sold for about $330 in 94-95..

I think this is a Astron from the sticker on the top,  The Td24 engine was a 24 cc model.  It had diffrent coloring and shape..

Friiy