Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

 It's official the honda 1132. A 11 hp. 32" inch cut tracked snowblower needs a retrofit kit to blow powdered snow without sucking it through the carburator and dieing.

 I was also informed that honda will only supply the kit  (its under warrenty) if the customer asks for it.

I am now waiting a week or more for a kit to come in so i can snowblow my driveway.

Have you tried to make an intake screen for your carb?  Something as simple as a piece of a nylon stocking stretched over the intake and held there with a tie wrap or piece of wire would probably do the job.

Thanks borat for the picture in my head of a Red Honda wearing Black Lace Stockings LMAO

its a good idea it should keep out the snow and it will get you going till that kit comes

Ron

cavebear53 wrote:

Don't recall recommending black.  I usually go with grand-ma beige.   Most Honda guys I know are into glitz.  So black will likely be their colour of choice.  Maybe a piece with little sequins in it for added flash....  

I had a snowmobile that would lose power in deep powder snow due to taking it into the carb.  The nylon stocking fixed the problem.  It's been on the machine for years and still looks in good shape.  Seems that stuff will last for ever. 

Make it a pair of really OLD nylons that are in the trash, Or YOU might end up in the

DOG HOUSE!!!!

Have a great NEW YEAR!!!

T.J.

i will try the nylon hose. I have a piece of vacume cleaner hose duct taped to it now with the far end looped up inside of my cab. But need to switch to larger hose to increase airflow. Gives a red green look

I just picked up the honda anti iceing kit for my 1132. Part #06196-ze3-305. This part keeps the snow from entering the carburator and stalling the engine.
 It should be standard equipment
  Honda will only supply it if you make a complaint about stalling. I had to make several complaints as they first told me i was only having problems because i had bought there big machine when most peaple wanted the small ones. They then told me not to worry about it because the next storms may not be powder. I still haven't  recieved any calls back from honda corp. maybe they took my comments about farm animals and needing to marry outside of there imediate family personaly.  I will have to contact them again.

Is this symptom of carb icing, and wet ignition from blowing snow into the wind > vs down< wind?
Thousands of hours, and have never had this issue on any machine.

the honda is sucking snow into the carb and causing the engine to blow black smoke and stall. When the carb cover is removed it is covered in drops of water that fall into the intake and cause problems. It was a swirling windy day  and i was often being covered with snow i ended up finishing with my mtd yardman it didn't suffer any problems just much harder to turn.

Is the 1132's air cleaner cover different from other models'? I ask 'cause I never experienced such a problem with my 928 even in the fluffiest snow conditions.

I just used my 1132 in heavy powder for the first time since installing the anti ice-ing kit  and had no problems with stalling. The dealer told me that this is the only model that has this issue. one of the salesman also told me it was because i bought there largest machine while most peaple only wanted the smaller units implying it was really my fault not theirs. Runs great now im glad i kept it.                                       

blunt wrote:
So it's the customer's fault if only the most popular models are properly equipped? I like your dealer's sense of humor lol. What does the anti-icing kit consist of? I suspect it's just the thick rubber shroud that covers the side of the engine where the carb is, must be worth what, $20? Pretty miserly of them to hold it back on a $2700 machine.

Gelid wrote:
 It a metal shroud and 2 pieces of rubber wrapped around the carb, Of course finding the fuel shutoff  is strictly a fumble and feel operation as it is completely covered by rubber

blunt wrote:
Yup. What you describe comes standard on the 928. They call the metal shroud 'carburetor cover'  even though it covers more than just the carb. As for the rubber wrap-around it has a slit for access to the shutoff valve but it doesn't align that good that's why you need to slide your fingers in there and feel for the lever. Does a pretty good job of keeping snow out though.