Outdoor Power Equipment (Lawn Mowers, Snow Blowers, Chain Saws and more) Discussions

The official product description for our snow thrower: Jacobsen Homelite Imperial SNO 826 eight HP Heavy Duty Two Stage Snow Blower with Electric Start and 4 forward speeds with reverse. My description: old, orange and until today, started every time.

Picked this up on craigslist this past summer from a retired mechanic who'd taken decent care of it and recently had replaced the electric start. Started and ran fine at that time and has worked fine for three snowfalls. Tried to fire it up today to no avail -- electric start does nothing and the cord is stuck like the engine is ceased. Oil was fairly recently changed prior to purchase and is full -- no leaks detected. Fuel was added about a month ago. One thing I neglected to do this time was close the valve between the fuel tank and carb before parking it. Was running fine when I last shut it down. Could the engine be shot? We've had a good cold snap, so cars are starting slow too -- no clue if the temp would affect this. Thanks much.

The other thing to do is to use a grease gun and inject grease through the grease nipples then rotate the augers by hand so that the grease is distributed. Do this a few times so that you have lots of grease between the drive shaft and the auger axle. This helps stop the drive shaft from rusting to the auger axle.

As far as the starter motor is concerned its just a matter of tightening up 4 bolts. If any of the bolts holes' thread are stripped then it gets trickier. I've had the same experience, for better than 99% of the time I just use the manual start.

&amp;lt;BR&amp;gt;&lt;BR&gt;<BR><SPAN CLASS="quotedmessageheader">nibbler wrote:</SPAN><BR><DIV CLASS="quotedmessage">The other thing to do is to use a grease gun and inject grease through the grease nipples then rotate the augers by hand so that the grease is distributed. Do this a few times so that you have lots of grease between the drive shaft and the auger axle. This helps stop the drive shaft from rusting to the auger axle.&amp;amp;lt;BR&amp;amp;gt;&amp;amp;lt;BR&amp;amp;gt;As far as the starter motor is concerned its just a matter of tightening up 4 bolts. If any of the bolts holes' thread are stripped then it gets trickier. I've had the same experience, for better than 99% of the time I just use the manual start.
<BR>quote]<BR>
Nibbler,Good call except you forgot to mention to Grease them when the shear bolts are not in thats the only to spin them.

I don't know what happened before:<BR>Nibbler,<BR>Good call except you forgot to mention to Grease them when the shear bolts are not in thats the only way to spin them.

hirschallan - Looks like your html commands are being interpretted as text.

I reread my comment and you're right I did sort of assume that you would do the greasing before replacing the shear bolts. Makes it easier to rotate the augers and its cheaper since you don't have to replace the bolts again :-).

Thanks -- the bolt explanation makes complete sense and I will pick up a few to keep on hand. The grease tip is helpful too.

The engine is pretty easy to start with the pull cord, so I won't be too upset if for some reason I am unable to reinstall the electric start.

Next thing I need to work on is the chute (sp?). At its base, the only thing holding it against the gear that rotates it are a few bolts/washers that it looks like someone added at some point. They're just loose enough to allow it to turn, but as you can imagine they rattle loose and frequently need to be tightened.

Three possible solutions:

1. Lock washer - problem is I keep loosing them; or
2. Lock nut - This looks like a regular nut but it has a plastic O-Ring in it. When you thread it on the bolt the plastic deforms and makes the nut very stiff to tighten or take off - problem they're basically use once; or
3. Use locktite - it basically glues your nut to the bolt. There are several levels, some more permanent than others, can be removed with acetone ( nail polish remover).

If you are a belt and suspenders sort of person do two or three.

Nibbler: All great ideas -- I think I even have some Locktite of the waterproof variety that should work for this. We're getting dumped on here in Minnesota today, and the blower has been working pretty well. Thanks for your various tips.

Where are you getting parts?  I have a part sheet from 2000 but can not find anyone that sells parts.  Need the roller bearings for the drive gear with the chain going to the wheel shaft.